Orion System SA Controller - Manual (Page 3)

SA Controller Operator’s Interface 3
Introduction
Modular System Manager
ENTER
CLEAR ESC
PREV NEXT
DOWN
UP
6 5 4
DEC
7
0
8
1 3 2
9
MINUS
-
STATUS
SETPOINTS
SCHEDULES
ALARMS
OVERRIDES
9.00"
6.25"
1.81"
Figure 2: Modular System Manager Dimensions
Description
The OE392-08 Modular System Manager provides a direct link to enable
you to view the status and adjust the setpoints of any controller on the
control system communications loop. The Modular System Manager is
designed to be used with the Orion Control System. The System Manager
is housed in an attractive, off-white colored plastic enclosure. The System
Manager is equipped with a 4-line-by-20-character backlighted display
panel and a 24-key membrane keypad for data selection and entry. All
keypad operations are simple and straight forward, utilizing non-cryptic
plain English language messages. Menu-driven programming allows for
easy setup and operation without the need for specialized training. The
System Manager also has 2 integral LEDs for user notifi cation of system
alarm conditions and override initiations. Protection from unauthorized
users is provided by the System Manager’s integral multi-level passcode
authorization programming.
On a Networked Orion System, the Modular System Manager is
connected to the communications and power loop of the system via
modular cables that simply plug into the System Manager board and
the Power/Comm Distribution Board. This virtually eliminates wiring
errors and makes installation fast and easy. When it is to be connected to
a Stand-Alone system, a cable with modular connectors on one end and
stripped wire ends on the other end is provided to facilitate connecting
communications and power to the Modular System Manager from the
24 VAC power source and the HVAC unit controller communication
wiring terminals.
The Modular System Manager is designed for wall mounting. Mounting
holes are provided to attach the Modular System Manager to a standard
handy box. It is recommended that the System Manager be mounted at
approximately eye level to allow for ease of programming and reading
of the display. The System Manager is typically mounted in the building
manager’s or superintendent’s offi ce or in an equipment room.
Modular Service Tool and System Manager
Modular Service Tool
Mode
Selection
ENTER
CLEAR ESC
PREV NEXT
DOWN
UP
6 5 4
DEC
7
0
8
1 3 2
9
MINUS
-
STATUS
SETPOINTS
SCHEDULES
CONFIGURATION
ALARMS
ON
OVERRIDES
BALANCE - TEST
10.00”
4.75”
2.02"
1.63"
Figure 1: Modular Service Tool Dimensions
Description
The OE391-08 Modular Service Tool is a system operator interface that
provides a direct link in viewing the status, confi guring, and adjusting
the setpoints of any SA Controller on the control system communications
loop. The Modular Service Tool is housed in an attractive beige-colored
plastic enclosure. The display area is covered with a clear plastic bezel
for protection of the display screen. The Modular Service Tool has a
4-line-by-20-character display panel with adjustable contrast control
and a 27-key membrane keypad for data selection and entry. All keypad
operations are simple and straight forward, utilizing non-cryptic plain
English language messages. Menu-driven programming allows for
easy setup and operation without the need for specialized training. The
OE391-08 Modular Service Tool is supplied with (4) AA 1.5 V Volt
alkaline batteries, a wall mount DC power supply and a communica-
tion cable terminated with an 8-pin DIN connector for connection to
the Service Tool. The cable allows you to setup and program your SA
Controller with an 8-pin DIN connector socket by simply plugging the
service tool into the socket on the controller.
The Modular Service Tool is designed to be hand-carried. Its rugged
plastic housing provides superior protection for the electronic compo-
nents housed inside. The OE391-08 Modular Service Tool is a top-quality
service tool that will stand up to the demands of the typical job site
environment for many years.