Option compatibility, 19) contains the code for the previous fault, Refer to drive fault trace register contents – Yaskawa APOGEE FLN P1 User Manual
Page 51: 13 option compatibility, Drive fault trace register contents
13
Option Compatibility
A limited number of options may be simultaneously connected to the drive depending on the
for more information. More details can be found in the
Options and Peripheral Devices chapter of the drive Technical Manual.
Table 18 Option Installation Compatibility
OptionConnector
Connector
Number of Possible Options
SI-C3, SI-J3, SI-N3, SI-P3, SI-S3, SI-EN3
etc.
<1>
CN5-A
1
PG-B3, PG-X3 etc.
CN5-B, C
2
<1>
DO-A3, AO-A3, AI-A3, DI-A3 etc.
CN5-A, B, C
1
<1>
The AI-A3 and DI-A3 options can be used to set the frequency reference or replace the drive analog inputs with
higher resolution when installed in CN5-A. These options can only be used for monitoring when installed in
CN5-B or CN5-C,; their input levels will be displayed in U1-17 or U1-21 to U1-23.
n
Drive Fault Trace Register Contents
Table 19 Drive Fault Trace Register Contents
Fault
Code
Fault Name
0002H
Undervoltage (Uv1)
0003H
Control Power Supply Undervoltage (Uv2)
0004H
Soft Charge Circuit Fault (Uv3)
0006H
Ground Fault (GF)
0007H
Overcurrent (oC)
0008H
Overvoltage (ov)
0009H
Heatsink Overheat (oH)
000AH
Heatsink Overheat (oH1)
000BH
Motor Overload (oL1)
000CH
Drive Overload (oL2)
000DH
Overtorque Detection 1 (oL3)
0010H
Braking Resistor Overheat (rH)
0011H
External Fault at Input Terminal S3 (EF3)
0012H
External Fault at Input Terminal S4 (EF4)
0013H
External Fault at Input Terminal S5 (EF5)
0014H
External Fault at Input Terminal S6 (EF6)
0015H
External Fault at Input Terminal S7 (EF7)
001BH
Input Phase Loss (PF)
001CH
Output Phase Loss (LF)
Fault
Code
Fault Name
001DH
Motor Overheat (PTC input) (oH3)
001EH
Digital Operator Connection (oPr)
001FH
EEPROM Write Error (Err)
0020H
Motor Overheat (PTC input) (oH4)
0021H
MEMOBUS/Modbus Communication Error
(CE)
0022H
Option Communication Error (bUS)
0027H
Option External Fault (EF0)
0028H
PI Feedback Loss (FbL)
0029H
Undertorque Detection 1 (UL3)
002BH
High Slip Braking Overload (oL7)
0030H
Hardware Fault (including oFx)
0036H
Output Current Imbalance (LF2)
0037H
Pullout Detection (Sto)
003BH
Too Many Speed Search Restarts (SEr)
0041H
PI Feedback Loss (FbH)
0042H
External Fault 1, Input Terminal S1 (EF1)
0043H
External Fault 2, Input Terminal S2 (EF2)
0046H
Current Offset Fault (CoF)
0047H
PLC Detection Error 1 (PE1)
13 Option Compatibility
YASKAWA TOEP YAICOM 13 Metasys N2 & Apogee FLN P1 SI-J3 Installation & Technical Manual
51