Optoma ZU725T 7800-Lumen WUXGA Laser DLP Projector - Manual (Page 86)

English 86
ADDITIONAL INFORMATION
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 n value
Read Command
Command Command
Pass
CMD
CMD Value CMD
Write Command
sp
ac
e Set
Para.
Service ~XX469 1~nnn.nnn.nnn.nnn
PJ Link Setup Apply
Off ~XX455 0
On ~XX455 1
Off ~XX457 0
On ~XX457 1
Off ~XX458 0
On ~XX458 1
Off ~XX459 0
On ~XX459 1
Reset ~XX181 1
1200 ~XX153 1 O k 1200
2400 ~XX153 1 O k 2400
4800 ~XX153 1 O k 4800
9600 ~XX153 1 O k 9600
19200 ~XX153 1 O k 19200
38400 ~XX153 1 O k 38400
57600 ~XX153 1 O k 57600
115200 ~XX153 1 O k 115200
Reset ~XX176 1
Regulatory ~XX151 3 O k nnnnnnnn
Serial Number ~XX353 1 O k nnnnnnnnnnnnnnnn
Projection Hours ~XX150 21 O k nnnnn (nnnnn= hour digits)
Standby Mode
Light Source Mode
Light Source Hours
~XX108 1 O k nnnnn (nnnnn= hour digits)
Total Hours ~XX108 1 O k nnnnn (nnnnn= hour digits)
Normal ~XX108 3 O k nnnnn (nnnnn= hour digits)
Eco Mode ~XX108 4 O k nnnnn (nnnnn= hour digits)
Custom Power ~XX108 7 O k nnnnn (nnnnn= hour digits)
Ambient Temp
Temperature
~XX150 18 O k nnn..nn (e.g. Ok48)
Projector ID ~XX79 00~99 ~XX558 1 O k 00~99
Remote Code ~XX350 00~99 ~XX138 1 O k 00~99
Network
LAN Interface
MAC Address
Network Status
DHCP
IP Address
Subnet Mask
Gateway
DNS
Control
Crestron
Extron
PJ Link
AMX
Telnet
HTTP
Input Signal
Resolution
Signal Format
Pixel Clock
Horz Refresh
Vert Refresh
Color Space
Picture Mode
Second Signal
Resolution
Signal Format
Pixel Clock
Horz Refresh
Vert Refresh
Color Space
Main Version
~XX122 1 O k nnnnnnn (FW)+
I-SCALER Version
F-MCU Version
Communication
Signal
Information
AMX
Telnet
HTTP
Serial Port In Baud Rate
Device
System Status
Extron
Note : Some commands are not supported, it depends on models 9 -
Note: Some commands are not supported, it depends on models .
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 n value
Read Command
Command Command
Pass CMD CMD Value CMD
Write Command
sp
ac
e Set
Para.
M-MCU Version
A-MCU Version
LAN Version
Formatter Version
HDBaseT Version
Camera Version
Other Items
Power Off ~XX00 0 ~XX124 1 O k 0
Power On ~XX00 1 ~XX124 1 O k 1
Power On with password ~XX00 1 ~nnnn
Restart ~XX00 3
Re-Sync ~XX01 1
Off ~XX02 0 ~XX355 1 O k 0
On ~XX02 1 ~XX355 1 O k 1
Unfreeze ~XX04 0
Freeze ~XX04 1
To Emitter ~XX232 0
To Next Projector ~XX232 1
3D Frame Delay 1~200 ~XX233 1~200
2D ~XX130 1 O k 0
3D ~XX130 1 O k 1
Standby Mode I N F O 0
Warming up I N F O 1
Cooling Down I N F O 2
Out of Range I N F O 3
lightsource Fail ( LED Fail) I N F O 4
Thermal Switch Error I N F O 5
Fan Lock I N F O 6
Over Temperature I N F O 7
LightSource Hours Running Out I N F O 8
Cover Open I N F O 9
lightsource Ignite Fail I N F O 10
Format Board Power On Fail I N F O 11
Color Wheel Unexpected Stop I N F O 12
Over Temperature I N F O 13
FAN 1 Lock I N F O 14
FAN 2 Lock I N F O 15
FAN 3 Lock I N F O 16
FAN 4 Lock I N F O 17
FAN 5 Lock I N F O 18
LAN fail then restart I N F O 19
LD lower than 60% I N F O 20
LD NTC (1) Over Temperature I N F O 21
LD NTC (2) Over Temperature I N F O 22
High Ambient Temperature I N F O 23
System Ready I N F O 24
I N F O 25
FAN 6 Lock I N F O 26
FAN 7 Lock I N F O 27
FAN 8 Lock I N F O 28
FAN 9 Lock I N F O 29
FAN 10 Lock I N F O 30
FAN 11 Lock I N F O 31
FAN 12 Lock I N F O 32
FAN 13 Lock I N F O 33
FAN 14 Lock I N F O 34
Green/Normal ~XX155 1 O k 1
Orange/Notice ~XX155 1 O k 2
Red/Warning. About to trigger shutdown ~XX155 1 O k 3
Green/Normal ~XX159 1 O k 1
Orange/Notice ~XX159 1 O k 2
Red/Warning. About to trigger shutdown ~XX159 1 O k 3
Device Type Projector ~XX149 1 O k 1
Model Name Optoma WUXGA ~XX151 1 O k 5
On ~XX239 1 ~nnnnnnnn ~XX229 1 O k 1
Off ~XX239 2 ~nnnnnnnn ~XX229 1 O k 0
System Temperature
Fan Status Level
OSD Lock
3D Sync Out
System Auto Send
Output 3D state
AV Mute
Firmware Version
Freeze
Note : Some commands are not supported, it depends on models 10 -