Document Outline

• FOREWORD
• SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS
  • Contact :
  • In USA:
  • Outside USA:
• REVISION LOG
• SECTION 1. SAFETY PRECAUTIONS
  • 1.1 GENERAL
  • 1.2 PRE-OPERATION
    • Operator Training And Knowledge
    • Workplace Inspection
    • Machine Inspection
  • 1.3 OPERATION
    • General
    • Trip and Fall Hazards
    • Electrocution Hazards
    • Tipping Hazards
    • Crushing And Collision Hazards
  • 1.4 LIFTING, AND HAULING
    • General
• SECTION 2. PREPARATION AND INSPECTION
  • 2.1 PERSONNEL TRAINING
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 2.2 PREPARATION, INSPECTION, AND MAINTENANCE
  • 2.3 PRE-START INSPECTION
  • 2.4 DAILY WALK-AROUND INSPECTION
    • Walk-Around Inspection Components
  • 2.5 FUNCTION CHECK
    • Function Check Items:
• SECTION 3. MACHINE OPERATION
  • 3.1 GENERAL
  • 3.2 MACHINE DESCRIPTION
  • 3.3 MACHINE OPERATION
    • Getting Started
  • 3.4 HOOD - (CARRY DECK)
    • Removal:
    • Installation:
  • 3.5 BATTERY CHARGING
    • Battery Low Voltage Warning Indicators
    • To Charge Batteries
    • Battery Charging Status Indicators
  • 3.6 GROUND CONTROL STATION - OPERATION
    • Platform/Off/Ground Selector Switch
    • Emergency Stop/Shut Down Button
    • Brake Release Button
    • Platform Up and Down Buttons
    • Machine Status LCD Display
    • Tilt Alarm Warning
    • LCD Display Fault Conditions
  • 3.7 PLATFORM CONTROL CONSOLE - OPERATION
    • General
    • Platform On/Off Key Switch
    • Platform Emergency Stop/Shut Down Button
    • Platform Control Display Panel
    • Drive/Lift Mode Selector Switch
    • Joystick Function Enable Lever
    • Multifunction Joystick Control
    • Horn Button
    • Drive Speed Setting Controls
  • 3.8 PLATFORM FUNCTION ENABLE FOOT SWITCH
  • 3.9 PLATFORM MANUAL DESCENT CONTROL VALVE
    • Activating the Manual Descent Valve
  • 3.10 PLATFORM CONFIGURATION
    • Platform Lanyard Anchorage Point
    • Material Handling Tray - Height Adjustment
    • Material Handling Tray - Cargo Strap - OPTION
  • 3.11 PARKING MACHINE
  • 3.12 TRANSPORTING, LIFTING AND TIE-DOWN PROCEDURES
    • General
    • Fork-Lift Truck Transport
    • Vehicle Transport - Tied-Down Using the Tie-Down Loops
  • 3.13 PROGRAMMABLE SECURITY LOCK (PSL™) (OPTION)
    • PSL™ Box Location
    • Machine - Power Up using the PSL™
    • Machine - Power Down
    • Changing the Operator’s Code
  • 3.14 PLATFORM HANGER ACCESSORY - (OPTION)
    • Hanger Accessory - Pre-Start Inspection
    • Loading and Transporting an Item using the Hanger Accessory
  • 3.15 RUG CARRIER ACCESSORY - (OPTION)
    • Pre-Start Inspection
    • Hanging a Rug
    • Removing a Rug
  • 3.16 FLOURSCENT TUBE CADDY - (OPTION)
    • Pre-Start Inspection
  • 3.17 DECAL INSTALLATION
• SECTION 4. EMERGENCY PROCEDURES
  • 4.1 GENERAL INFORMATION
  • 4.2 EMERGENCY OPERATION
    • Operator Unable to Control Machine
    • Platform Caught Overhead
  • 4.3 INCIDENT NOTIFICATION
• SECTION 5. GENERAL SPECIFICATIONS AND OPERATOR MAINTENANCE
  • 5.1 INTRODUCTION
  • 5.2 GENERAL SPECIFICATIONS
    • Machine Specifications
    • Electrical Specifications
    • Platform Data
    • Machine Component Weights
    • Serial Number Location
  • 5.3 OPERATOR MAINTENANCE
    • Lubrication
  • 5.4 Battery Maintenance
  • 5.5 Tires and Wheels
    • Tire Wear and Damage
    • Wheel and Tire Replacement
    • Wheel Installation
  • 5.6 GROUND CONTROL STATION - PROGRAMMING
    • General
    • Programming Levels
    • Operator Programming Mode
    • Tilt Sensor
    • Programming Items
    • Activating Programming Mode
    • Entering Password
    • Programming Mode Selection
    • Selecting Programmable Item to Adjust
    • Adjusting Programmable Setting
  • 5.7 DRIVE MOTOR BRUSH WEAR - WARNING INDICATION
• SECTION 6. INSPECTION AND REPAIR LOG