Accessories, Warning – Lincoln Electric PIPELINER 200 User Manual
Page 18
ACCESSORIES
C-2
C-2
PIPELINER® 200D KUBOTA
WIRE FEED OPTIONS
Wire Feed Module (K623-1) - Provides constant volt-
age (CV) output with improved arc stability for
Innershield welding. Excellent for MIG welding.
Recommended wire feeders are the LN-7, LN-23P and
LN-25. (Factory installed on the K1643-6).
LN-15 Wire Feeder (K1870-1,-2)-Portable CC/CV unit
for flux-cored and MIG welding.
LN-23P Wire Feeder (K316L-1)-
Portable CV unit for
Innershield pipe welding. Control cable operates con-
tactor inside Wire Feed Module for “cold” electrode.
Requires LN-23P Adapter Kit (K350-1) and Gun and
Cable Assembly.
LN-23P Adapter Kit (K350-1)-
Required to adapt LN-
23P to any Lincoln power source. Makes 14 pin con-
nection at power source.
Magnum® 250 Innershield Gun (for LN-23P) (K355-10)-
For lighter weight and easier handling. Rated 250
amps, 60% duty cycle. For .068 through 5/64” (1.7
through 2.0 mm) Innershield wire and includes
reduced speed switch. For pipewelding, an M11476
62° gun tube is recommended.
LN-25 Wire Feeder (K449)-
Portable CC/CV unit for
flux-cored and MIG welding. Includes Gas Solenoid &
Internal Contactor. Requires Wire Feed Module.
Remote Voltage Control Kit for LN-25 (
K444-2)
Provides 25 ft. (7.5m) of remote output voltage control
and output jumper (2 and 4) for machines having 14
pin MS-type connector.
Magnum® 350 Innershield Gun (for LN-25)(K126-2)-
For self-shielded wire with 15 ft. (4.5m) cable. For
.062-3/32” (1.6-2.8mm) wire.
Magnum® 200 MIG Gun (for LN-25)(K497-3)-
With
15 ft. (4.5m) cable. For .025 (0.6m) wire.
Magnum Gun Connector KiT (K466-1)
Connects
Magnum 200 MIG gun to LN-25 Wire Feeder.
62° gun tube for Pipe Welding (KP1909-1)-
Recommended modification for K355-X or K345-X
guns with 90° gun tubes. Compatible with K126-1,-2
K264-8 and K355-10.
OPTIONAL FEATURES
(Field Installed)
GENERAL OPTIONS
Pipe Thawing with an arc welder can cause fire,
explosion, damage to electric wiring or to the arc
welder if done improperly. The use of an arc welder
for pipe thawing is not approved by the CSA, nor is
it recommended or supported by Lincoln Electric.
------------------------------------------------------------------------
Spark Arrestor Kit (K903-1) - Includes a heavy gage
steel, approved spark arrestor, clamp and adapter for
mounting to the muffler exhaust pipe.
TRAILER (K953-1) - Two-wheeled trailer with optional fender
and light package. For highway use, consult applicable feder-
al, state, and local laws regarding possible additional require-
ments. There is a choice of 2 hitches, a fender & a light pack-
age.
K953-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-1 Fender & Light Kit
K965-1 Cable Rack
K1858-1 AIR CLEANER SERVICE INDICATOR
STICK OPTIONS
K704 ACCESSORY SET - Includes 35 ft.(10 m) of
electrode cable and 30 ft.(9 m) of work cable, head-
shield, work clamp and electrode holder. Cable is rated
at 500 amps, 60% duty cycle.
Remote Control Kit (K924-5) - Contains remote
control rheostat and 100 ft.(30.5 m) cable for adjusting
the OCV at the welding site. (For Codes 10910 and
above.)
Remote Control Kit (K2464-1) - Contains a remote
control rheostat (for adjusting the CC “STICK” OCV),
remote control potentiometer (for adjusting the CV
“WIRE” OCV), and 100ft.(30.5m) cable.
WARNING