Yokogawa ADMAG AXF - Manual (Page 115)

IM 01E20D01-01E 6-53
6. OUTLINE
᭹ Unless otherwise specified, difference in the dimensions are refer to the following table.
Above Equal or below Above Equal or below
Category of basic dimension Category of basic dimension
Tolerance Tolerance
3 (0.12)
6 (0.24)
10 (0.39)
18 (0.71)
30 (1.18)
50 (1.97)
80 (3.15)
120 (4.72)
180 (7.09)
250 (9.84)
315 (12.40)
400 (15.75)
3 (0.12)
6 (0.24)
10 (0.39)
18 (0.71)
30 (1.18)
50 (1.97)
80 (3.15)
120 (4.72)
180 (7.09)
250 (9.84)
315 (12.40)
400 (15.75)
500 (19.69)
Ϯ0.7 (Ϯ0.03)
Ϯ0.9 (Ϯ0.04)
Ϯ1.1 (Ϯ0.04)
Ϯ1.35 (Ϯ0.05)
Ϯ1.65 (Ϯ0.06)
Ϯ1.95 (Ϯ0.08)
Ϯ2.3 (Ϯ0.09)
Ϯ2.7 (Ϯ0.11)
Ϯ3.15 (Ϯ0.12)
Ϯ3.6 (Ϯ0.14)
Ϯ4.05 (Ϯ0.16)
Ϯ4.45 (Ϯ0.18)
Ϯ4.85 (Ϯ0.19)
500 (19.69)
630 (24.80)
800 (31.50)
1000 (39.37)
1250 (49.21)
1600 (62.99)
2000 (78.74)
2500 (98.43)
630 (24.80)
800 (31.50)
1000 (39.37)
1250 (49.21)
1600 (62.99)
2000 (78.74)
2500 (98.43)
3150 (124.02)
Ϯ5.5 (Ϯ2.17)
Ϯ6.25 (Ϯ0.25)
Ϯ7.0 (Ϯ0.28)
Ϯ8.25 (Ϯ0.32)
Ϯ9.75 (Ϯ0.38)
Ϯ11.5 (Ϯ0.45)
Ϯ14.0 (Ϯ0.55)
Ϯ16.5 (Ϯ0.65)
Remarks: The numeric is based on criteria of tolerance class IT18 in JIS B 0401.
General tolerance in the dimensional outline drawing.
Unit : mm (approx.inch)
■ SIZING DATA (Measurable flow velocity is from 0 m/s.)
32
Size: mm
Flow velocity
(m/s)
Flow velocity
(ft/s)
Flowrate (GPM)
33
5.0
1.0
10
2.0
SI Units
10,000 1.0 1,000 100 10 0.1 0.01
English Units
Flowrate (m /h)
Size: inch
F44.EPS
* Measurable flow velocity is from 0 m/s.
15 25 40 50 65 80 100 125 150 200 250 300 350
10,000
400
0.5
1.0
5.0
10.0
0.3
10
5
1,000 100 10 0.1 0.01
2.5
0.001 100,000
500600 700 8009001,000
0.1
1
1,100 1,200
1,350
1,500
1,600
1,800
2,000
2,200 2,600
2,400
3
0.33
36
40
20 24
100,000
28 32 54 48
60
44
1,000,000
64 104 80 96 88
72
0.1 0.2 0.4 1 1.5 2.5 2 0.5 3 4 6 5 8 10 12 14 16 1.25