Rockwell Automation 1203-SM1 SLC to SCANport Communication Module - Manual (Page 51)

4–23 Using Enhanced Mode
Publication 1203–5.9 –– October 1996
The following data table shows the data to be sent to the SLC to
SCANport module via the SLC backplane.
address 15 data 0
O:1 0000 0000 0000 0000 SCANport Channels 1 & 2 Channel Command
O:1.1 0000 0000 0000 0000 SCANport Channel 3 Channel Command
O:1.2 0000 0000 0000 0000 SCANport Channel 1 Logic Command
O:1.3 0000 0000 0000 0000 SCANport Channel 1 Reference
O:1.4 0000 0000 0000 0000 SCANport Channel 2 Logic Command
O:1.5 0000 0000 0000 0000 SCANport Channel 2 Reference
O:1.6 0000 0000 0000 0000 SCANport Channel 3 Logic Command
O:1.7 0000 0000 0000 0000 SCANport Channel 3 Reference
O:1.8 0000 0000 0000 0000 SCANport Channel 1 Datalink A1 In
O:1.9 0000 0000 0000 0000 SCANport Channel 1 Datalink A2 In
O:1.10 0000 0000 0000 0000 SCANport Channel 1 Datalink B1 In
O:1.11 0000 0000 0000 0000 SCANport Channel 1 Datalink B2 In
O:1.12 0000 0000 0000 0000 SCANport Channel 1 Datalink C1 In
O:1.13 0000 0000 0000 0000 SCANport Channel 1 Datalink C2 In
O:1.14 0000 0000 0000 0000 SCANport Channel 1 Datalink D1 In
O:1.15 0000 0000 0000 0000 SCANport Channel 1 Datalink D2 In
O:1.16 0000 0000 0000 0000 SCANport Channel 2 Datalink A1 In
O:1.17 0000 0000 0000 0000 SCANport Channel 2 Datalink A2 In
O:1.18 0000 0000 0000 0000 SCANport Channel 2 Datalink B1 In
O:1.19 0000 0000 0000 0000 SCANport Channel 2 Datalink B2 In
O:1.20 0000 0000 0000 0000 SCANport Channel 2 Datalink C1 In
O:1.21 0000 0000 0000 0000 SCANport Channel 2 Datalink C2 In
O:1.22 0000 0000 0000 0000 SCANport Channel 2 Datalink D1 In
O:1.23 0000 0000 0000 0000 SCANport Channel 2 Datalink D2 In
O:1.24 0000 0000 0000 0000 SCANport Channel 3 Datalink A1 In
O:1.25 0000 0000 0000 0000 SCANport Channel 3 Datalink A2 In
O:1.26 0000 0000 0000 0000 SCANport Channel 3 Datalink B1 In
O:1.27 0000 0000 0000 0000 SCANport Channel 3 Datalink B2 In
O:1.28 0000 0000 0000 0000 SCANport Channel 3 Datalink C1 In
O:1.29 0000 0000 0000 0000 SCANport Channel 3 Datalink C2 In
O:1.30 0000 0000 0000 0000 SCANport Channel 3 Datalink D1 In
O:1.31 0000 0000 0000 0000 SCANport Channel 3 Datalink D2 In
Datalinks
A simple datalink application on a 1336 PLUS drive is to set a
parameter number into one of the Data In parameters. The SLC
output image word for that datalink will then control the value of that
parameter.