Contents and technical specifications, Caution – Futaba 8FGAS, 8FGHS 2.4GHz User Manual

Page 11

Advertising
background image

11

<Before Use>

Contents and Technical Specifications

(Specifications and ratings are subject to change without notice.)

Your 8FG SUPER includes the following components:

• T8FGS transmitter for airplanes or helicopters
• R6208SB Receiver
• HT6F1700B Ni-MH battery & Charger
• Switch harness
• Neck strap
*The set contents depend on the type of set.

Transmitter T8FGS

(2-stick, 14-channel, FASST-2.4G system)
Transmitting frequency: 2.4GHz band
Modulation: 2.4G 7-ch or 2.4G Multi-ch, switchable
Power supply: 7.2V HT6F1700B Ni-MH battery

Receiver R6208SB

(FASST-2.4G system, dual antenna diversity, S.BUS system)
Power requirement: 3.7V~7.4V battery or regulated

output from ESC, etc. (*1)

Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)
Weight: 0.49 oz. (13.8g)
(*1) When using ESC's make sure that the regulated

output capacity meets your usage application.

(Suggested Servo for use with your 8FG SUPER system)
Servo S9252 (Digital servo)

Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 V (from receiver)
Output torque: 91.7 oz.-in. (6.6 kg-cm) at 4.8V
Operating speed: 0.14 sec/60 at 4.8V
Size: 1.57 x 0.79 x 1.44 in. (40 x 20 x 36.6 mm)
Weight: 1.76 oz. (50 g)

Servo S9255 (Digital servo)

Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 V (from receiver)
Output torque: 125.0 oz.-in. (9.0 kg-cm) at 4.8V
Operating speed: 0.16 sec/60 at 4.8V
Size: 1.57 x 0.79 x 1.44 in. (40 x 20 x 36.6 mm)
Weight: 1.94 oz. (55 g)

Servo S3151 (Standard, Digital servo)

Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 V (from receiver)
Output torque: 43.1 oz.-in. (3.1 kg-cm) at 4.8V
Operating speed: 0.21 sec/60 at 4.8V
Size: 1.59 x 0.79 x 1.42 in. (40.5 x 20 x 36.1 mm)
Weight: 1.48 oz. (42 g)

Servo S3001 (Standard, ball-bearing)

Control system: Pulse width control, 1.52 ms neutral
Power requirement: 4.8 - 6.0V (from receiver)
Output torque: 41.7 oz.-in. (3.0 kg-cm)
Operating speed: 0.22 sec/60
Size: 1.59 x 0.78 x 1.41 in. (40.4 x 19.8 x 36 mm)
Weight: 1.59 oz. (45.1g)

Usage condition on "High Speed mode"

(R6208SB)

 CAUTION



When using the R6208SB in the high speed

(HS) mode, digital servos are required for

the first six channels (1-6).

If an analog servo is connected to one of the first

six channels when in the high speed mode, the

servo will not function properly. Additionally,

while many peripheral devices will operate in either

the high speed or normal mode, some will not. If

there are any difficulties noted, please return the

reciever's operational mode to the "Normal" mode

to determine if this resolves the difficulty.

If using the R6208SB in the high speed mode,

analog servos may be used for channels seven and

eight.

(For Operation Mode Selection, see p.26)

Advertising