LAARS M4-LHS - Installation Manual - Manual (Page 19)

HT# 059295-00
A
M4-LHS installation and Operation Manual
19
STarTuP SETTiNgS
Program Change Switch Setting
To be able to change the M4-LHS settings the Program/Run Switch must be set to Program.
The switch is located under the Enclosure Wiring Cover for security.
SYSTEM
A
B
C
D
1 2
RUN PROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
3 4 5 6 7 8 9 10 11 12 13 15 14 17 16 18 20 19 21 24 23 29 25 27 26 28 32 30 31
L N
- + + T T O O RS-485 mA GND VLT
SYS A B C D PWR
CUR / VLT
A
- + +
mA GND VLT
- + +
mA GND VLT
+ +
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
O O
TEMP
SYSTEM EXTENSION
MODULE CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION: RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
M4-LHS
HYBRID CONTROL
Startup Sequence
Button: MENU/<System Startup>
• When powered, the M4-LHS performs a self diagnostics-test.
• On the first power up, the System Startup screen will appear after the initialization is
complete. If it doesn’t, the M4-LHS has already been configured.
• The System Startup menu sets the main parameters that relate to the heating application.
These settings must be set by the installer.
-------- SETTINGS ----
Season Winter
System Target 140 o F
<System Settings>
<Maintenance>
<Histories>
<System Startup>
BACK ▲ ▼ SELECT
Boiler Type
Modulation, Hybrid Default: Modulation
Button: MENU/<System Startup>/..../Boiler Type
• The same Laars control can operate modulating boilers or a combination of both types.
• The Modulation option will operate a variety of modulating boiler signals.
• The Hybrid option will sequence two groups of boilers, condensing and non-condensing.
Each group could be of a different boiler type (Modulation or Staging). See "Hybrid Logic
Overview" on page 3. Each Multi-Stage boiler will use a single output relay for each stage.
• If BACnet is to be used, each of the Boiler Type modes will have a different set of BACnet
variables. See "Hybrid - Outdoor Reset - BACnet Variable list" on page 44.
--- BOILER TYPE ---
Modulation
Hybrid
BACK ▲ ▼ SAVE
Sensor Type
Reset °F, Reset °C, Set Point °F, Set Point °C, 4-20mA EMS Default: Reset °F
(Set Point Options are Not Available with Hybrid Boiler Type)
Button: MENU/<System Startup>/..../Sensor Type
• If Reset °F is selected, all temperatures and settings will be displayed in degrees Fahrenheit
and the control will use Reset Ratios to adjust the system set point.
• If Reset °C is selected, all temperatures and settings will be displayed in degrees Celsius and
the control will use Reset Ratios to adjust the system set point.
• If Set Point °F is selected, all temperatures and settings will be displayed in degrees
Fahrenheit and the control will have an adjustable system set point.
• If Set Point °F is selected, all temperatures and settings will be displayed in degrees Celsius
and the control will have an adjustable system set point.
• The 4-20mA EMS option is only available to the Hybrid Boiler Type option. To use
4-20mA EMS with Modulating Boiler Type, select one of the Set Point options and the EMS
Input Mode menu will follow to offer the 4-20mA EMS option.
• The use of the 4-20mA EMS option requires the purchase of the 4-20mA EMS Interface. It
gives the M4-LHS the capability of accepting a remote 4-20mA signal from a BMS or EMS
system as the target set point.
• If BACnet is to be used, each of the Sensor Type modes will have a different set of BACnet
variables. See "Hybrid - Outdoor Reset - BACnet Variable list" on page 44.
Modulating Options
-- SENSOR TYPE --
Reset o F
Reset o C
Set Point o F
Set Point o C
BACK ▲ ▼ SAVE
Hybrid Options
--- SENSOR TYPE ---
Reset o F
Reset o C
4-20mA EMS
BACK ▲ ▼ SAVE
EMS input Mode
Disable, Enable Default: Disable
(Available after Set Point with Modulation Boiler Types)
Button: MENU/<System Startup>/..../Boiler Type/Sensor Type / EMS Input Mode
• It allows the M4-LHS to utilize the 4-20mA EMS Interface to accept a remote 4-20mA
signal from a BMS or EMS system as the target set point.
- EMS INPUT MODE -
Disable
Enable
BACK ▲ ▼ SAVE