Ri-200 repeater controller system command list – Pacific Research Solutions RI-200 User Manual
Page 76
Pacific Research Solutions
RI-200 User Manual
Page 75
RI-200 REPEATER CONTROLLER SYSTEM COMMAND LIST
System
Command
System Command Description
and Data Format
Command
Syntax
Factory
Setting
Pwr on
Recover
00
No Operation
Used for clearing a macro area
00
N/A
N/A
01
System mode
Mode 0 = System off, 1 = COS, 2 = CTCSS/DCS,
3 = COS and CTCSS/DCS, 4 = Open squelch,
5 = No repeat audio, 6 = No repeat audio or PTT.
01 [Mode]
1
COS
Yes
02
RX Source mode
Mode 1 = Reject sub audio, 2 = Pass sub audio,
3 = De-emphasis & reject sub audio,
4 = De-emphasis and pass sub audio.
02 [Mode]
1
Reject
sub audio
Yes
03
Reserved
03 [ ]
N/A
N/A
04
Repeater carrier delay time
Time = 0 - 255 in 1/10 second increments.
04 [Time]
30
3.0 Sec
Yes
05
Force on repeater PTT for set time
Time = 0 - 3600 second.
05 [Time]
0
0 Sec.
No
06
Repeater telemetry mode
No Mode = Suppress function complete and error one time.
Mode 0 = Disable (off), 1 = ID only,
2 = Function complete and ID only, 3 = All enable (on).
06 [Mode]
3
All on
Yes
07
Station ID interval time
Time = 0 - 255 in 6 seconds increments, 0 = Disable
07 [Time]
100
10.0 Min
Yes
08
Courtesy message timer, COS falling to start of message
Time = 0 - 99 in 1/10 second increments, 0 = Disable
08 [Time]
20
2.0 Sec.
Yes
09
LED Status Display (lowers current drain)
Mode 1 = Enable (on), 0 = Disable (off)
09 [Mode]
1
on
Yes
10
Repeater time-out time
Time = 0 - 255 in 6 seconds increments, 0 = Disable, * = Reset
10 [Time]
30
3.0 Min.
Yes
11
Reserved
11 [ ]
N/A
N/A
12
Transmit audio output adjust
Adj. = 0 - 63 or * up one count, # down one count
12 [Adj]
RI-200 = 31
RI-210 = 9
Yes
13
Reserved
13 [ ]
N/A
N/A
14
User and S-Command control CTCSS/DCS tone panel enable
Panel 0 = Both, 1 = User-Commands, 2 = S-Commands
Mode 1 = Enable (on), 0 = Disable (off)
14 [Panel] [Mode]
0
Both off
Yes
15
User command group decode enable
Group = 0 – 8, 0 = All groups
Mode 1 = Enable (on), 0 = Disable (off)
15 [Group] [Mode]
1&2 on
3 – 8 off
Yes
16
DTMF Decode Inter digit time
Time = 1 - 99 in 1/10 seconds increments
16 [Time]
35
3.5 Sec.
Yes
17
DTMF Decode Mute time
Time = 0 - 99 in 1/10 seconds increments, 0 = No mute
17 [Time]
25
2.5 Sec.
Yes
18
DTMF Mute control
Mute 0 = All, 1 = Repeater, 2 = Auxiliary, 3 = Telephone
Mode 1 = Enable (on), 0 = Disable (off)
18 [Mute] [Mode]
1
All on
Yes
19
Resend DTMF on repeater
Digits = 0 to 9, A, B, D, *, # (34 digits max.)
19 [Digits]
N/A
No