Fostex VF80EX - Manual (Page 130)

130
Save/Load of Song data (VF80EX)
Warning!
You are responsible for use of this digital de-
vice. Be sure to abide by the copyright condi-
tions of the source material.
Press “Enter/Yes” key if you agree with the
above.
<Hint>
The warning message above also appears when
setting the “
Digital In setting ” menu to “ On ”.
See “ Setup mode ” on page 130 for details.
<Note>
If you do not agree with the warning message con-
tents, press the
[EXIT/NO] key to quit loading.
The display briefly shows “Set Disable” and “ Can’t
Loading” , then returns to the mode select screen.
If you agree with the warning message contents,
go to the next step to continue the operation.
<Warning message>
The warning message for copyright shown on the
screen is as follows.
If you agree to the message contents, press the [EN-
TER/YES] key.
The display changes to show the screen for selecting
the load type, on which “One” flashes.
You can select a desired load type from among the
following.
Select the desired “One” or “Select”.
Depending on the selected load type, the display
shows as below.
• When selecting “One” or “Select”:
The left column shows the track numbers (01, 02...)
of the audio CD, while “NON” in the sewcond column
shows no program is selected.
“**” is shown when more than one track is recorded
on the audio CD. It is not shown when only one track
is recorded on the audio CD.
To select desired tracks to be loaded, go to step 8.
6
7
One
Select
All
You can select one or more tracks to be loaded.
Each selected track is individually loaded to a new
program automatically created on the current drive.
You can select one or more tarcks to be loaded. All
the selected track are loaded to a new program
automatically created on the current drive.
All the tracks on an audio CD are loaded to a new
program automatically created on the current drive.
* “A new program automatically created on the current
drive” has the program number one higher than
the current highest program number.
• When selecting “All”:
All tracks on the audio CD are selected to be loaded,
and the screen as shown below appears. In this screen
example, the destination program newly created on
the current drive is “P05”. Each track time is also
shown.
When selecting “All”, you can start loading tracks to
the current drive by pressing the [ENTER/YES] key
while holding down the [RECORD] key.
You can delete an unnecessary track if you want. See
<Hint> below about how to do it.
<Hint>
Before executing “All” track loading, you can de-
lete ahn unnecessary track by the following proce-
dure.
1) While the display shows the screen as above, use
the [JOG] dial (or the [CURSOR] keys) to
highlight the desired track and press the
[ENTER/YES] key.
The destination program number of the selected
track starts flashing.
2) Use the [JOG] dial (or the [CURSOR] keys) to
select “NON” and press the [ENTER/YES] key.
A track whose destination program number is
set to “NON” is not loaded.
Use the [JOG] dial (or the [CURSOR] keys) to select
(highlight) a desired track to be loaded and press the
[ENTER/YES] key.
The load destination program number of the selected
track is shown as a flashing display, as well as the
track time. In the screen example below, track 1 (01)
is selected. The total time is also shown above the track
list. (The total time is summed up each time you se-
lect another track.)
8
Un this condition, you can choose the option between
“Pxx” (program number) and “NON” using the [JOG]
dial (or the [CURSOR] keys). To cancel the track selec-
tion, choose “NON” and press the [ENTER/YES] key.
To set the track to be loaded, go to the next step.