Fostex VF80EX - Manual (Page 65)

65
Recorder Functions (VF80EX)
7
8
6
• To set editing points by marks:
Press the [TIME BASE SEL] key.
Each data field for the Start, End and To points changes
to show the current option by mark as shown below.
Use the [CURSOR / ] keys to highlight the field for the
desired point, and press the [ENTER/YES] key.
The field starts flashing.
Use the
[JOG] dial to select the desired mark and press
the [ENTER/YES] key.
The point is set to the selected mark.
<Note>
This operation can be performed only when any mark
is set. When no mark is set, "
00:ABS 0 " is the one and
only option for each point.
Use the [CURSOR ] key to highlight the field ("01"
above) for the number of times for repeat paste, and
press the [ENTER/YES] key.
" 01 " starts flashing and you can now enter the number
of times for repeat paste.
Use the [JOG] dial to select the desired number and
press the [ENTER/YES] key.
You can select any number between " 01 " and " 99 ".
<Note>
Basically you can select the number of times for repeat
paste between 1 and 99, however, if the recordable space
of the hark disk is limited, you may not be able to select
the desired number. The VF80EX automatically calcu-
late the available space and limit the number of times to
the appropriate value.
When setting the number of times for repeat paste to 02,
the copy & paste function is performed as below.
A''
A'' A A'
A'
START Point END Point TO Point
Copy & paste within the same track.
Copy & paste between different track.
Press the [UNDO/REDO/F3] key while holding down the
[SHIFT] key.
The copy & paste (or move & paste) function is per-
formed. When finished, "
Completed! " appears on the
screen.
<Hint>
You may use the [CURSOR >] to highlight " EXE " and press
the [ENTER/YES] key to perform the function, instead of
pressing the [UNDO/REDO/F3] key while holding down the
[SHIFT] key.
<Note>
The copy & paste (or move & paste) operation cannot be
performed when there is not enough disk space to per-
form the undo and redo operations. If you try to perform
the paste operation when there is not enough disk space,
The display will show "
Over Time! ", as well as the short
time.
In such a case, shorten the copy (or move) data by the
amount more than the displayed time or delete unnec-
essary sections or programs to keep the enough space,
and then try to paste again.
Undo/redo of Copy & Paste
You can undo a copy & paste or move & paste opera-
tion, as well as redo it (undo the undo operation).
• By pressing the [UNDO/REDO] key after completing the
copy & paste (or move & paste) operation, you can
return the track(s) to the condition before performing
the copy & paste (or move & paste) operation.
• By pressing the [UNDO/REDO] key just after
performing the undo operation, you can undo the undo
operation and return the track(s) to the condition
after performing the copy & paste (or move & paste)
operation.
Note the following for performing the undo/redo opera-
tion.
<Notes>
You can undo or redo only when the recorder is stopped.
If you carry out any of the following after performing the
copy & paste (or move & paste) operation, you cannot
undo/redo the copy & paste (or move & paste) opera-
tion.
1.Making a new recording
2.Performing a new editing
3.Letting the recorder run in playback (or recording)
mode and pass through the auto punch-in point while
the auto punch mode is active
4.Turning off the power of the VF80EX
5.Performing any of the program operations (select,
rename or delete).