Fostex VF80EX - Manual (Page 64)

64
Recorder Functions (VF80EX)
or "MovePaste"
6
1
2
3
4
5
Performing Copy (or Move) & Paste
Set the Start and End points for the copy (or move)
operation and To point for the paste operation.
Using the digital scrub function, set the Start, End and
To points. See "
Storing the digital scrub point " for details
about how to set the points.
While the recorder is stopped, press the [TRACK EDIT]
key.
The screen for selecting the track edit type appears.
Use the [JOG] dial to select "Copy Paste" (or "Move
Paste") and then press the [ENTER/YES] key.
The display shows the screen for selecting the source
track(s) and destination track(s).
Use the [JOG] dial to select the source track(s) from
which the data is copied (moved).
Rotating the [JOG] dial changes the options among 1
through 8, 1&2, 3&4, 5&6, 7&8, 1-6, and 1-8.
Use the [CURSOR ] key to highlight (and flashes) the
right field, and use the [JOG] dial to select the destina-
tion track(s) to which the data is copied (moved).
Rotating the [JOG] dial changes the options as below
depending on the track(s) you selected in step 4.
Source track(s) Destination options
a mono track (1 through 8) 1 through 8
a pair of tracks 1&2, 3&4, 5&6, and 7&8
1-6 1-6 only
1-8 1-8 only
In the example below, data on tracks 3&4 is copied (or
moved) and pasted onto tracks 7&8.
The corresponding [TRACK STATUS/TRACK SEL] keys of
the source track(s) light in green, while the correspond-
ing
[TRACK STATUS/TRACK SEL] keys of the destination
track(s) light in red.
Press the [ENTER/YES] key after selecting tracks.
The display shows the " Point Select " screen as below, in
which you can view the Start, End and To points set via
the digital scrub operation.
<Hints>
On the screen above, you can perform the following
operations.
1. Editing the Start, End and To points
2. Setting the Start and To points to "ABS 0" and the End point
to "REC END"
3. Checking the data to be copied (or moved)
4. Setting the Start, End and To points by marks
• To edit the Start, End and To points:
Highlight the time field of the desired (Start, End or To) point,
and then press the [ENTER/YES] key.
The " seconds " value starts flashing, showing that you can
edit it. Use the [CURSOR / ] keys to move the flashing
value, and use the [JOG] dial to enter a value.
After entering the desired time, pressing the [ENTER/YES]
key to store the time data to the point.
• To set the Start and To points to "ABS 0" and the End
point to "REC END":
Press the [SETUP/F1] key while holding down the [SHIFT] key.
" ALL OFF " changes to " ALL ON ", and the Start and To
points are set to " ABS 0 ", while the End point is set to " REC
END " point. This function is useful when you copy (or
move) all track data (from "ABS 0" to "REC END") to dif-
ferent track(s).
• To check (monitor) the data to be copied (or moved)
[Source Play function]:
Press the [TIME BASE SEL/F2] key while holding down the
[SHIFT] key.
The display shows the " Source Play " screen as shown
below and the recorder starts playback of the data to be
copied (or moved).
You can hear audio by moving up the corresponding track
fader. After checking audio, press the
[STOP] key.
The display returns to the screen shown before perform-
ing the Source play function.