Panasonic WJ-SX 150 - Manual (Page 48)

50
SETUP PROCEDURES
■ Setup Procedures
This unit has two setting procedures.
The one is SETUP MENU, which is the unit's on-screen dis-
play (OSD).
The other is WJ-SX150 Administrator Console, which oper-
ates on the PC.
• SETUP MENU (OSD)
The basic functions, which are essential for the operation,
are configurable. However, some items are not config-
urable. The settings about group sequences, operators and
schedules, etc.
• WJ-SX150 Administrator Console (PC)
All the functions of this unit are configurable. You need a
PC to use WJ-SX150 Administrator Console.
Refer to p. 64 WJ-SX150 ADMINISTRATOR CONSOLE for
details of the platform and installation.
Notes:
• To use WJ-SX150 Administrator Console, you need to
prepare a PC and a 9-pin D-sub cable.(Refer to p. 47.)
• When changing the configuration of WJ-SX150
Administrator Console, configuration data getting and
putting are necessary between the unit and PC to acti-
vate your configuration.
■ Description of Setup Procedures
This chapter describes about configurable items.
● Sequence Settings
SETUP MENU can configure tour sequences. WJ-SX150
Administrator Console can configure both of tour
sequences and group sequences.
• Tour sequence: Up to 16 tour sequences are config-
urable (16 steps per tour).
• Group sequence: Tour sequences can be activated on
up to 4 monitors simultaneously (1 tour sequence per
monitor).
● Schedule Settings
SETUP MENU can configure daylight saving time. WJ-
SX150 Administrator Console can configure timer event,
camera cleaning, and daylight saving time.
• Timer event: A sequence or spot mode can be activat-
ed on the regular time of every month, week or day.
Up to 30 timer events can be registered.
• Camera cleaning: Camera cleaning can be executed
on the regular time of every month, week or day.
• Daylight saving time: Daylight saving times for 20 years
are configurable.
● Alarm Settings
The operation parameters when an alarm is input to the unit
are configurable.
• Alarm mode: The operation mode activated along with
an alarm input is configurable. Sequence mode or hold
mode is selectable. Alarm mode can be set to OFF
when not using it.
• Alarm event: The event activated along with an alarm
input is assignable to each alarm input terminals. The
sequence number or spot camera is selectable for the
alarm event.
• Alarm input (Alarm port): The alarm polarity (N. O. or N.
C.) is assignable to each alarm input terminal. One of
16 terminals is assignable for time adjustment.
SETUP MENU (OSD)
WJ-SX150 Administrator Console (PC)
Sequence settings
• Tour sequence
• Group sequence
Schedule settings
• Timer event
• Camera cleaning
• Daylight saving time
Alarm settings
• Alarm mode
• Alarm event
• Alarm input/Alarm port
Operator settings
• Operator registration
• Level table
• Monitor select (Monitor selection)
• Auto login/logout (Auto log-in/log-out)
System settings
• Clock (Time and date) *
1
• Cable compensation
• Camera title
• Data port *
2
Multiplxer board
• Recorder
• Multiplexer *
3
• Mux (Multiplxer camera title) * 3
Setup file operation
• Put a file to SX150
• Get a configuration data from the SX150
SX150 Admin Console Configuration
• File Open
• Account Manager
• Communication (Serial) port
• Camera manual cleaning ON/OFF
* 1 WJ-SX150 Administrator Console can configure the
display pattern.
* 2 WJ-SX150 Administrator Console can configure the
communication speed (baud rate) of the ports Data 1 to 4.
* 3 These menus (or windows) appear only when the Multiplxer
is installed in the unit.