Panasonic AG-3DP1G - Manual (Page 71)

1
Chapter
4

Adjustments
and
Settings
for
Recording
•RECWARNING
This is displayed during a recording error. Do the
recording over. If this does not solve the problem,
consult your supplier.
•
CARDERRL(R)(L/R):
This indicates trouble with the P2 card(s)
inserted into the card slot(s).
• Turn the power off if the warning continues.
• If the warning persists after rerecording, replace
the card with another card.
• IRREGULARFRMSIG:
The reference signal, such as the GENLOCK
input, is distorted.
•
L/RDURATIONNG:
The duration of the recorded clip is different
between the L and R P2 cards.
•
OVERMAX#CLIPS:
The limit for the number of clips
that can be recorded to one P2 card has
been reached.
•
PULLDOWNERROR:
Video pull-down sequence
error in a mode such as 24P (25P)
•
RECRAMOVERFLOW:
Overflow of recording memory
•
ERROR:
Other causes
•RUNDOWNCARDL(R)(L/R)
This message indicates that a P2 card has been
overwritten the maximum number of times and that
normal recording cannot be guaranteed if operation
continues.
It is best to replace such P2 cards with a new card.
•SYSTEMERROR
This message indicates that a system error has
occurred. This type of error can often be corrected by
turning off the power and turning it back on again.
•
CAMMICONERROR: The microprocessor in the
camera is not responding.
• PCONTROLERROR: A P2 control error has
occurred.
•
PMICONERROR:
The P2 microprocessor does not
respond
•
PMICONLINKERROR:
A connection error between
P2 microprocessors has occurred.
•THUMBNAILOPEN
This message is displayed in the viewfinder during
thumbnail operations.
•TURNPOWEROFF
This message indicates that an abnormal event has
occurred, for example, that a card was removed during
access or that a system mode change was made.
Turn the power off and then turn it back on again.
•WARNING
These messages are displayed when an error related to
the camera block is detected.
•
FOCUSNGL(R)(L/R): Focus error
•
ZOOMNGL(R)(L/R):
Zoom error
•
IRISNGL(R)(L/R):
Iris error
•
NDFILTERNGL(R)(L/R):
ND filter error
• CONV.NGL(R)(L/R): Convergence error
•
SUBLENSNGL(R)(L/R):
Sub-lens error
•VERSIONMISMATCH
PLEASEUPDATE
This message is displayed if a version mismatch has
occurred.
Perform card updating.
•WIRELESSRF
This message indicates that reception from the wireless
receiver is poor.
Camera status display
•ABB
ABB indicator
•AUTOKNEE(ON/OFF)
Displayed when changing the AUTO KNEE switch
position.
•AWB
AWB indicator
•AWBP3.K/AWBP5.K
Displays the color temperature assigned to PRST when
the WHITE BAL switch is set to PRST. Also displayed
when AWB is performed in the PRST position.
•GAIN  dB
Displayed when GAIN is switched.
•SHUTTER  (OFF)
Displayed when the shutter speed is changed.
3D status display
•3DASSIST
• ALERT(ON/OFF): Status indication of the 3D ASSIST
ALERT function
•
CONV.(ON/OFF):
Status indication of the 3D ASSIST
CONV. function
•3DASSISTACTIVE
Displayed when the ZEBRA button is pressed while the
3D assist function is active.
•3DMODE
• NEAR: Displayed when the 3D MODE selector switch
position is changed to NEAR
•
NORMAL:
Displayed when the 3D MODE selector
switch position is changed to NORMAL.
•
EXTRAZOOM:
Displayed when the 3D MODE
selector switch position is changed to EXTRA.