CHAMPION DH5000T Single Source Gas Manual - Manual (Page 122)

114
For
m No. 115074_rev
. A
P/N 900958 Contr
ol Box W
all Mount Kit
(for Direct V
ent Option Model & Condensate Removal Option Model)
Installation Instructions: Over
view:
The Direct V
ent Model and the Condensate Removal Model
utilize a separate control box that is inter
wired to the dishwasher
.
The standard configuration calls for this box to mounted to the left-hand side of the machine; however
, the control box can be mounted to the
wall if desired. The following instructions describe the steps necessar
y
to mount the control box using the par
ts included in the Control Box
W
all Mount Kit P/N 900958.
Dish T
able
Dish T
able
Dish T
able
Dish T
able
Control
Box
Dish table
Figure 1 –
The straight-through operation machine
shown with control box mounted on wall.
! VER
Y IMPORT
ANT !
The contr
ol box can only be mounted within the limits of the prewired
cables connecting the contr
ol box and the dishwasher together
.
Refer to Figure 2 and Figure 3 in the Installation Instructions below
for additional information concerning the location of the contr
ol box.
Figure 2 –
For the Straight-through Operation machine,
the control box can be mounted on the right-hand or
left-hand side of the machine.
Figure 3 –
For the Cor
ner Operation machine,
do not mount the control box in the black area shown
on the right-hand side machine.
1
Control Box Location
Refer to Figures 2 and 3. Note the gray and black shaded areas. The gray area indicates the approximate allowed location to mount the control box; black indicates the area where the control box must not be mounted. In all circumstances, the mounting location of the control box must not inter
fere with the
operation of the hood nor prevent access to the dishwasher for ser
vicing.
The control box can only be mounted within the limits of the prewired cables connecting the control box and the dishwasher togther
.
NOTE: The control box and cables
weigh 10 lbs./4.1 kg.
2
Check the Kit par
ts
Refer to T
able 1 at right and make sure your kit contains the par
ts listed.
The W
all Mount Bracket T
emplate is located on the reverse side of this sheet.
! A
TTENTION !
THE F
ASTENERS NEEDED TO A
TT
ACH THE CONTROL BOX
TO THE W
ALL ARE NOT INCLUDED IN THE KIT
.
THESE F
ASTENERS ARE SUPPLIED BY OTHERS.
3
Mounting the Box
Refer to Figure 4: Install the wall mount brackets (Item 1) to the back of the control box using the four screws (Item 2) supplied in the Kit. Position the control box in the desired location & make sure the cables are not overextended. Using the template, on the reverse side of this sheet, (Item 3), mark the location of the four mounting holes for the wall mount brackets on the suppor
ting wall.
See Figure 5: The control box assembly weighs 10 lbs./4.1 kg and must be mounted with the appropriate fasteners for the type of suppor
ting wall.
The fasteners are supplied by others. The control box installation is complete.
Figure 4 –
The location of the control box
must be mounted within the limits
of the interconnecting cables
without overextending the cables.
Figure 5 –
The control box assembly weighs 10 lbs/4.1 kg
and must be mounted with the appropriate
fasteners for the type of suppor
ting wall.
The fasteners are supplied by others.
TABLE 1 - Kit Par
ts List
Item Par
t
Description
Qty
.
No. No.
1
334473
Bracket, W
all Mounting
2
2
100212
Screw
, 10-32 x 3/4" T
russ Head
4
3
115074
Template, W
all Mount Bracket
1
(T
emplate on reverse side of this sheet)
1
2
3
1
W
all
fasteners supplied by others
Cor
ner
Operation
Straight-through
Operation
~ 6-1/2"
~12-9/32"
Scale 1/1
W all Mount Bracket
Template P/N 115074
For
Model DH5000 Direct V
ent Option and
Condensate Removal Option
Electrical Control Box Top W
all Mount Bracket
Bottom W
all Mount Bracket
1/4" Hole
1/4" Hole
1/4" Hole
1/4" Hole
See Reverse Side for Installation Instructions