INFICON HLD6000 Refrigerant Leak Detector Interface Description - Manual (Page 8)

8 ASCII Protocol
2.3 Commands
Command Meaning
Relates
to LD
cmd. no.
Read /
Write
*BEEP Output beep sound. Parameter: Typ,Volume
"*BEEP 1,2"
Typ: 1= 2000 Hz, 2=Dual (2000 and 1000 Hz), 3= 1000 Hz
Volume: Volume between 1 and 15 W
*CAL Start external calibration 4 W
*CAL:ACKnowledge Acknowledge stable signal during external calibration 11 W
*CLS Clear Error 5 W
*CONFig:AUDio Audio alarm type (PIN, SET, TRIG, OFF) 600 R/W
*CONFig:BRIGHTness Sniffer white LED brightness 414 R/W
*CONFig:BUTSniffer button of the sniffer probe (OFF, ON) 422 R/W
*CONFig:CALleak leak rate of external test leak R/W
*CONFig:CALleak:G/a leak rate of external test leak in g/a 388 R/W
*CONFig:CALleak:LB/yr leak rate of external test leak in lb/yr R/W
*CONFig:CALleak:MBAR*l/s leak rate of external test leak in mbar*l/s R/W
*CONFig:CALleak:OZ/yr leak rate of external test leak in oz/yr R/W
*CONFig:CALleak:PA*m3/s leak rate of external test leak in Pa*m3/s R/W
*CONFig:CALREQInterval calibration request interval in minutes (0=calibration
request off) 418 R/W
*CONFig:GAS Gas type (smart probe only)
(R134A, R22, R404A, R407C, R410A, R1234YF, R32,
USER1, USER2, USER3) 486 R/W
*CONFig:LIGHTAlarm Sniffer white LED alarm configuration:
DISABLED: always same brightness
ON: higher brightness if trigger 1 is exceeded
BLINK: blink, if trigger 1 is exceeded 413 R/W
*CONFig:PLCINLINK Assignment of PLC-inputs
*CONFig:PLCINLINK:1 for PLC input Pin1
*CONFig:PLCINLINK:2 for PLC input Pin2
...
*CONFig:PLCINLINK:10 for PLC input Pin10 438 R/W
*CONFig:PLCINLINK:1 Configuration of PLC-input. The following settings are
possible: NOT_USED, EXT_CAL, START, STOP,
CLEAR, START_STOP, VALID_TRIGGER. 438 R/W
*CONFig:PLCINLINK:n n = 2…10 see CONFig:PLCINLINK:1 438 R/W
*CONFig:PLCOUTLINK Assignment of PLC-outputs
*CONFig:PLCOUTLINK:1 for Pin 1
*CONFig:PLCOUTLINK:2 for Pin 2
...
*CONFig:PLCOUTLINK:8 for Pin 8 263 R/W
*CONFig:RECorder:LINK1 Function at analog output channel 1
(OFF, LR_LIN, EXTERN) 222 R/W
*CONFig:RECorder:LINK2 Function at analog output channel 2
(OFF, LR_LIN, EXTERN) 222 R/W
*CONFig:RECorder:UPPERVAL Upper limit for the analog out at IO module.
The value sets the leak rate in g/a for an output voltage of
10V 225 R/W
*CONFig:RS232 Protocol (ASCII, LD, HLD4000, SIMPLE) 26 R/W