Tweco 200 XT Auto-Cut 400V - Manual (Page 57)

AUTO-CUT 200 XT
Manual 0-5284 OPERATION 4-11
Code Message Remedy / Comments
227
Inverter 2A Incom-
patible Revision
Unsupported Inverter Revision; Ribbon cable CCM J33 to Inverter Module 2 Section A dam-
aged; CCM code version incompatible with Inverter revision or model
228 Not used Reserved for other models with additional inverter sections.
229 Not used Reserved for other models with additional inverter sections.
230 Not used Reserved for other models with additional inverter sections.
231
Inverter 1A VAC
Mismatch
Inverter AC Voltage rating incompatible with Power Supply voltage rating; Ribbon cable
CCM J31 to Inverter Module 1 Section B damaged or loose; Wrong voltage Inverter Module 1
installed; Defective Inverter module
232
Inverter 1B VAC
Mismatch
Inverter AC Voltage rating incompatible with Power Supply voltage rating; Ribbon cable
CCM J32 to Inverter Module 1 Section B damaged or loose; Wrong voltage Inverter Module 1
installed; Defective Inverter module
233
Inverter 2A VAC
Mismatch
Inverter AC Voltage rating incompatible with Power Supply voltage rating; Ribbon cable
CCM J33 to Inverter Module 2 Section A damaged or loose; Wrong voltage Inverter Module 2
installed; Defective Inverter module
234 Not used Reserved for other models with additional inverter sections.
235 Not used Reserved for other models with additional inverter sections.
236 Not used Reserved for other models with additional inverter sections.
237
Too Few Inverters
Found
Two or more Inverter Sections required to operate; Ribbon cable from CCM to Inverter Section
damaged or disconnected;
238 BIAS VAC Invalid Invalid AC Voltage Selection; Damaged or loose connection at J61 of System Bias Supply
239 AC Voltage High
System Bias PCB detected AC Voltage is higher than Power Supply rated Voltage; System
Bias Supply J61 Voltage Selection connection damaged or disconnected; Defective System
Bias PCB; Defective CCM
240 AC Voltage Low
System Bias PCB detected AC Voltage is lower than Power Supply rated Voltage; System
Bias Supply J61 Voltage Selection connection damaged or disconnected; Defective System
Bias PCB; Defective CCM
241
Inverter 1A Input
Voltage Error
Inverter Input Voltage fault; voltage out of range or missing phase at AC Input of Inverter
Module 1 Section A; Poor AC Power Quality; Defective W1 contactor; Loose or open connec-
tion between input terminals and W1 contactor or contactor and input of Inverter Section;
Defective Inverter module
242
Inverter 1B Input
Voltage Error
Inverter Input Voltage fault; voltage out of range or missing phase at AC Input of Inverter
Module 1 Section B; Poor AC Power Quality; Defective W1 contactor; Loose or open connec-
tion between input terminals and W1 contactor or contactor and input of Inverter Section;
Defective Inverter module
243
Inverter 2A Input
Voltage Error
Inverter Input Voltage fault; voltage out of range or missing phase at AC Input of Inverter
Module 2 Section A; Poor AC Power Quality; Defective W1 contactor; Loose or open connec-
tion between input terminals and W1 contactor or contactor and input of Inverter Section;
Defective Inverter module
244 Not used Reserved for other models with additional inverter sections.
245 Not used Reserved for other models with additional inverter sections.
246 Not used Reserved for other models with additional inverter sections.
247
Inverter 1A Circuit
Fault
Inverter Module 1 Section A detected a circuit fault; Damaged Inverter Module 1
248
Inverter 1B Circuit
Fault
Inverter Module 1 Section B detected a circuit fault; Damaged Inverter Module 1