Great Plains YP1625A Operator Manual User Manual
Operator, Manufacturing, inc
Advertising
Manufacturing, Inc.
© Copyright 2012
Printed 2013-08-13
401-625M
EN
ORIGINAL INSTRUCTIONS
Operator
YP1225A & YP1625A
30- and 40-Foot 2-Section Yield-Pro
®
Planters
with Air-Pro
®
Seed Meters
Read the operator manual entirely. When you see this symbol, the
subsequent instructions and warnings are serious - follow without
exception. Your life and the lives of others depend on it!
Illustrations may show optional equipment not supplied with standard unit or may
depict similar YP1225 or YP1625 models where a topic is identical.
29618
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- Operator
- Table of Contents
- Important Safety Information
- Look for Safety Symbol
- Be Aware of Signal Words
- Prepare for Emergencies
- Be Familiar with Safety Decals
- Wear Protective Equipment
- Use A Safety Chain (Hydraulic Hitch)
- Avoid High Pressure Fluids
- Handle Chemicals Properly
- Keep Riders Off Machinery
- Use Safety Lights and Devices
- Transport Machinery Safely
- Shutdown and Storage
- Tire Safety
- Practice Safe Maintenance
- Safety At All Times
- Safety Decals
- Safety Reflectors and Decals
- 818-055C Slow Moving Vehicle Reflector
- 838-266C Red Reflectors
- 838-265C Amber Reflectors
- 838-267C Daytime Reflectors
- 818-590C Danger: Crushing Hazard
- 838-599C (Option) Danger: Electrocution Hazard
- 818-045C Warning: Pinch-Crush
- 818-339C Warning: High Pressure Fluid Hazard
- 818-580C (Option) Warning: Overhead Hazard
- 818-579C (Option) Warning: Pinch-Shear Hazard
- 818-188C Warning: Excessive Speed
- 818-398C Caution: Tires Not A Step
- 818-578C Caution: Tire Pressure
- 838-995C Caution: General
- 858-011C Warning: Tire Pressure
- Introduction
- Preparation and Setup
- Initial Setup
- Pre-Planting Setup
- Hitching Tractor to Planter
- Operating Instructions
- Pre-Start Checklist
- Wing Lock Overview
- Unfolding The Planter
- Raising/Lowering Planter
- Folding the Planter
- Transporting
- Loading Materials
- Fertilizer Tanks (Option)
- Field Setup Checklist
- Monitor Operation
- Electric Clutch Operation
- Hydraulic Drive Operation (Option)
- Air System Operation
- Marker Operation
- Field Operation
- Parking
- Storage
- Adjustments
- Setting Material Rates
- Fan and Meter Pressurization Adjustment
- Checking Planting Rate
- Setting Fertilizer Rate
- Marker Adjustments
- Height Switch
- Row Implement Adjustments
- 25 Series Row-Unit Adjustments
- Troubleshooting
- Maintenance and Lubrication
- Maintenance
- Material Clean-Out
- Meter Brush Maintenance
- Bleeding Hydraulics
- Marker Maintenance
- Hydraulic Drive Maintenance
- Chain Maintenance
- Meter Drive Chain
- Disc Spreaders and Scrapers
- Fertilizer System Maintenance
- Seed Flap Replacement
- Seed Flap Replacement
- Lubrication
- Caster Arm Pivot
- Marker Hinges
- Parallel Pivot Arms
- Tool Bar Pivot
- Tool Bar Pivot
- Tongue Lift Cylinder Anchor Pin
- Tongue Slide Roller
- Wing Pivot, Vertical
- 25 Series Side Wheel Bushing
- Frame-Mounted Coulter Hub (Option)
- Frame-Mounted Coulter Pivot (Option)
- Caster Wheel Pivot
- Wing Transfer Drive Shafts
- Rockshaft Pivot Pins
- Drive Chains, Contact Drive
- Drive Chains, Fertilizer Pump (Option)
- Drive Chains, Ground Drive
- Drive Chain, Hydraulic Drive (Option)
- Drive Chains, Seed Meter
- Drive Chains, Wing
- Main Transport Wheel Bearings
- Gauge Wheel Bearings
- Marker Disk Hubs
- Walkboard Pivot
- Row Cleaner Bearings (Option)
- Seed Lubricant
- Options and Accessories
- Appendix A - Reference Information
- Appendix B - Pre-Delivery
- Appendix C - Initial Setup
- Appendix D - Option Installation
- Appendix R - Row Pro
- Index