SINGER 518 Stylist User Manual
SINGER Sewing machines
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- GENERAL PURPOSE FOOT AND NEEDLE PLATE
- STRAIGHT STITCH FOOT AND NEEDLE PLATE
- FEED COVER NEEDLE PLATE
- SPECIAL PURPOSE FOOT
- BUTTONHOLE FOOT
- ZIPPER FOOT
- BLINDSTITCH HEM GUIDE
- CHANGING PRESSER FEET
- CHANGING NEEDLE PLATES
- BOBBINS
- NEEDLES
- CHANGING THE NEEDLE
- STITCH PATTERN DISCS
- FABRIC, THREAD AND NEEDLE TABLE
- THE NEEDLE THREAD
- Threading the needle
- RAISING THE BOBBIN THREAD
- You are now ready to sew
- SETTING THE MACHINE
- CHOOSING ACCESSORIES
- STARTING TO SEW
- ADJUSTING STITCH LENGTH
- ADJUSTING PRESSURE
- REGULATING THREAD TENSION
- PIN BASTING
- STARTING A SEAM
- KEEPING THE SEAM STRAIGHT
- TURNING SQUARE CORNERS
- GUIDING AND SUPPORTING THE FABRIC
- CURVED SEAMS
- REINFORCING END OF SEAM
- ADJUSTING WIDTH OF DESIGN
- ADJUSTING STITCH PLACEMENT
- ADJUSTING NEEDLE-THREAD TENSION
- ADJUSTING STITCH LENGTH
- ADJUSTING PRESSURE AND CHOOSING ACCESSORIES
- ACCESSORIES AND SELECTOR SETTINGS
- Adjusting Stitch Length
- Adjusting Thread Tension
- PATTERNS PRODUCED BY FLEXI-STITCH DISCS
- FLEXI-STITCH DISC PATTERNS
- BASIC ZIG-ZAG PATTERNS
- To Produce a Flexi-Stitch Disc Pattern
- To Produce a Basic Zig-Zag Pattern with a Flexi-Stitch Disc
- Adjusting Width of Design
- Adjusting Stitch Placement
- Adjusting Needle-Thread Tension
- SETTING STITCH LENGTH DIAL
- ADJUSTING STITCH BALANCE
- ADJUSTING PRESSURE AND CHOOSING ACCESSORIES
- SETTING THE MACHINE
- Straight Stitching
- Zig-Zag Stitching
- INSERTING THE TWIN NEEDLE
- BUTTONHOLE POSITION
- BUTTONHOLE LENGTH
- Step 3: Side Stitching
- BALANCING THE TWO LINES OF STITCHING
- STRETCH STITCH CHART
- PLAIN STRETCH SEAMS
- Procedure
- GUIDING AND SUPPORTING FABRIC
- LADDER SEAMS
- OVEREDGED SEAMS
- Method #2 — Mock Overedging
- FINISHES FOR HEMS AND FACINGS
- LEATHER-LOOK VINYL t
- ZIPPERS
- Attaching the Zipper Foot
- CORDED SEAMS
- BLINDSTITCH ZIPPER INSERTION
- SEAMS IN FABRICS THAT RAVEL
- Darts in Interfacing
- APPLIQUÉ
- Method# 1 —Trimming after Stitchirrg
- Stitching after Trimming
- Hemstitched Appliqué
- HEMSTITCHING
- Preparation
- Procedure
- PICOT EDGES
- Procedure
- PATCHWORK QUILTING
- Procedure
- SMOCKING
- Procedure
- MENDING
- Mending a Tear
- Bar Tacks
- Repairing Stretch Garments
- Repairing Seams
- Darning without Embroidery Hoop
- Darning with Embroidery Hoop
- Preparation
- CAUTION: Before cleaning your machine, disconnect power-line plug from electrical supply.
- CAUTION: Before removing covers, bobbin case, and light bulb, disconnect power-line plug from electrical supply.
- REMOVING AND REPLACING TOP COVER
- REMOVING AND REPLACING BOTTOM COVER
- REMOVING AND REPLACING
- CARRYING CASE BASE
- REMOVING AND REPLACING
- FACE PLATE
- REMOVING AND REPLACING BOBBIN CASE
- • To remove bobbin case:
- • To replace bobbin case:
- CHANGING THE LIGHT BULB
- Removing the Bulb
- Replacing the Bulb
- REPLACING THE SLIDE PLATE
- REMOVING MACHINE
- FROM CABINET
- IMPORTANT;
- SINGER Oil
- DELUXE MONOGRAMMER No. 171278
- INDEX
- 9€WinG Micmtii 01BIM€T;