Hypertherm MAX200 Service Manual - Manual (Page 206)

Changed
Page
Description of change for revision 15 (date of change - 4/2008)
Revision
change pages
Added changes for revisions 14 and 15. Pages moved to the end of the manual.
i - x
Updated EMC and Warranty information to the latest version. Updated table of contents to reflect changes
for the new revision.
Section 1, 1a,
and 1b
Updated section 1 and 1a with the latest safety sections. Added the Spanish safety section (1b).
4-7
Changed part numbers for items 3, 4, and 24. 005088 to 005151, 005168 to 005187, and 075104 to
075394 respectively.
4-13 Changed part number for item 7 from 008316 to 008945.
4-15
Added a note to "shield gas SA" to see page 4-23. Removed components for "Incoming power TB1 SA"
(029316) and made 02916 item number20. Renumbered item numbers 24 through 26. They are now item
numbers 21 through 23.
4-17 through
4-19
Changed the part number for the chopper SA from 129118 to 129789.
4-23 Added a note to "shield gas SA" to see page 4-15.
4-25 Removed "HF & I/O PCB SA (029312) and item numbers 16 and 17.
4-29
Changed heat exchanger part number from 027136 to 027978. Added part number 128410 (coolant
reservoir upgrade kit), and a note for older systems.
4-30
Changed the part number for the lamp holder from 005088 to 005151.Changed the part number for the
coolant filter from 027137 to 027005. Changed coolant pump SA (029325) to a kit number (128384).
4-29 Corrected the part number for item 14 (from 029618 to 129618)
4-31 Corrected the part number for the torch main body. It was 020584 and changed to 120584.
4-35
Replaced obsolete part numbers for 90° hand torches with 25 foot (073008 to 073189) and 50 foot leads
(073009 to 073190).
4-36
Changed the part number for the 25 foot water cooled cable from 023324 to 023013. Changed the part
number for the 50 foot water cooled cable from 023325 to 023199.
4-44 through
4-48
Changed the part number and description for item number 8 from 046061 (2 inch ID tinned braid) to
046114 (1.5 inch ID tinned braid).
4-51 and 4-53
Changed the part number for item number 4 from 009336 to 009871 (same change for item number 13 on
page 4-53).Changed the part number for item number 26 from 002176 to 002127.
4-57 and 4-69
Changed the part number for "swivel #4" (below item number 12) from 015006 to 015259. Also added fer-
rule (015140) on page 4-69.
4-63 Removed part number 023098 (10 foot [3m]).
4-65
Removed part numbers 027109 and 046023, and added the part number for the heat shrink that is used
now, 004656.
4-82 Added part number for screws 075365 (qty 8).
Ap-c Schematics 013179 and 029313 changed from 8.5 x 11" to 11 x 17 fold outs.
Changed
Page
Description of change for revision 14 (date of change - 2/2000)
3-32 Revised chopper figure to new configuration.
4-1 General correction; PAC200E Gouging.
4-11 Revised item 2A and 2B part numbers.
4-15 Revised item 14 part number.
4-23 Revised item 1 part number.
4-45 and 4-46 Note added about extended leads over 75' causing start problems.