Verilink NCM 2000 (880-502623-001) Product Manual - Manual (Page 54)

Administration Menu
3-12
Verilink NCM 2000
Figure 3-10 Modem Configuration Menu
where:
The Modem Status is either CONNECTED or NOT CONNECTED.
Connected means that the modem is outputting the Data Carrier
Detect (DCD) lead as a HIGH, indicating a connection has been
made to another modem. If the NCM always shows connected for
this value, it might indicate that the modem has been optioned to
force DCD on at all times.
The upper part of the menu contains commands in the left column
and their affected parameter fields in the right column.
Change the appropriate parameters as necessary by typing the
command option character on the parameter line. You will be
prompted for your entry.
Table 3-4 Table 3-4 Table 3-4 Table 3-4 Modem Commands Modem Commands Modem Commands Modem Commands
-- MODEM CONFIGURATION MENU -- -- MODEM CONFIGURATION MENU -- -- MODEM CONFIGURATION MENU -- -- MODEM CONFIGURATION MENU --
Modem Status: NOT CONNECTED
Modem Status: NOT CONNECTED Modem Status: NOT CONNECTED Modem Status: NOT CONNECTED
D) Answer: DISABLED
D) Answer: DISABLED D) Answer: DISABLED D) Answer: DISABLED
C) Answer command: AT &C1&D2&K3 S0=1
C) Answer command: AT &C1&D2&K3 S0=1 C) Answer command: AT &C1&D2&K3 S0=1 C) Answer command: AT &C1&D2&K3 S0=1
T) Answer inactive timeout: 0 seconds
T) Answer inactive timeout: 0 seconds T) Answer inactive timeout: 0 seconds T) Answer inactive timeout: 0 seconds
B) Dial-Out: DISABLED
B) Dial-Out: DISABLED B) Dial-Out: DISABLED B) Dial-Out: DISABLED
U) Dial-Out command: AT &C1&D2&K3 X4 S0=0 DT
U) Dial-Out command: AT &C1&D2&K3 X4 S0=0 DT U) Dial-Out command: AT &C1&D2&K3 X4 S0=0 DT U) Dial-Out command: AT &C1&D2&K3 X4 S0=0 DT
N) Dial-Out number:
N) Dial-Out number: N) Dial-Out number: N) Dial-Out number:
R) Dial-Out connect retries: 0
R) Dial-Out connect retries: 0 R) Dial-Out connect retries: 0 R) Dial-Out connect retries: 0
K) Dial-Out connect timeout: 60 seconds
K) Dial-Out connect timeout: 60 seconds K) Dial-Out connect timeout: 60 seconds K) Dial-Out connect timeout: 60 seconds
I) Dial-Out inactive timeout: 0 seconds
I) Dial-Out inactive timeout: 0 seconds I) Dial-Out inactive timeout: 0 seconds I) Dial-Out inactive timeout: 0 seconds
S) Dial-Out W) Set default commands S) Dial-Out W) Set default commands S) Dial-Out W) Set default commands S) Dial-Out W) Set default commands
H) Hangup A) Answer
H) Hangup A) Answer H) Hangup A) Answer H) Hangup A) Answer
X) exit menu
X) exit menu X) exit menu X) exit menu
[0.0.0.5] [3,11] NCM 2000 >
[0.0.0.5] [3,11] NCM 2000 > [0.0.0.5] [3,11] NCM 2000 > [0.0.0.5] [3,11] NCM 2000 >
Command
Usage
D Answer. Toggles auto-answer mode On/Off. ENABLED = on, DISABLED = off
C
Answer Command. Initialization string sent to modem when auto-answer is enabled,
verify commands in modem manual if auto-answer does not function.
T
Answer Inactive Timeout. Time in seconds NCM will wait for Data Carrier Detect (DCD)
after going off-hook to answer an incoming call, value of zero disables this option and
allows modem shift register 7 to handle timeout.
B
Dialout. Toggles dialing out to Trap Host On/Off. If ENABLED NCM will attempt to dial
Trap Host(s) sequentially when it has alarms to report. If DISABLED NCM will never dial
out.
U
Dial-Out Command. Command string sent before the phone number when NCM dials
out. Typically includes S0=0 to turn off auto-answer for duration of the dial-out
session as well as DT to use DTMF (touch tone) dialing.
N
Dial-Out number. The phone number to be dialed when the NCM dials out.