Verilink SCC 2020 (880-503268-001) Product Manual User Manual

Page 20

Advertising

Quick Set-Up

2-6

Verilink SCC 2020 User Manual

Now type “D2”, the prompt

enter port 2 channels >

enter port 2 channels > appears. Type

“13-24”. Press E

NTER

by itself to refresh the display with the DS0

assignments.

Figure 2-4 DIU 2130 Configuration Menu

Lead toggles are used to determine whether the control leads on
the synchronous serial interface will function in the normal way or
be forced on. When the DTE does not assert control leads they can
be forced on by typing the three letter abbreviation of the control
lead. For this example the DTE supports normal control lead
operation and the default values are appropriate.

Mode is used to determine the data rate of each of the timeslots
assigned to the port. In the case of an AMI T1 circuit the mode must
be 56K. For the B8ZS T1 used in this example, 64K gives the user
greater throughput. Use the M1 and M2 commands to set both data
ports to 64K per DS0.

The remaining options are correct for this example. The T1 circuit
and DTE should now be connected.

Once the CSU has been connected to the T1 circuit for at least
fifteen minutes, meaningful performance statistics will be available
under the Performance Menu, see

Chapter 4

for more details.

Within 15 seconds of connecting the T1 circuit, the NET LED on the
front of the SCC 2020 should change from red to green. If it does
not, the Diagnostics Menu may be used for troubleshooting, see

Chapter 5

for more information on diagnostics.

--- DIU 2130 CONFIGURATION/DIAGNOSTIC MENU ---

C) CSU [ 1,1 ]

C) CSU [ 1,1 ]
T) timing source CSU

T) timing source CSU

chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

chnl 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Dp)port 01 01 01 01 01 01 01 01 01 01 01 01 02 02 02 02 02 02 02 02 02 02 02 02

Dp)port 01 01 01 01 01 01 01 01 01 01 01 01 02 02 02 02 02 02 02 02 02 02 02 02

Lead Toggles DTR) DSR) RTS) CTS) DCD)

Lead Toggles DTR) DSR) RTS) CTS) DCD)
Forced Ports -/- -/- -/- -/- -/-

Forced Ports -/- -/- -/- -/- -/-

Port 1 Port 2 Statistics

Port 1 Port 2 Statistics
Mp) mode 56K 56K FW/HW Rev.............1.6/0.8

Mp) mode 56K 56K FW/HW Rev.............1.6/0.8

Mp) mode 56K 56K FW/HW Rev.............1.6/0.8
Sp) scram/hdlc inv N/N N/N Battery...............OK

Sp) scram/hdlc inv N/N N/N Battery...............OK

Sp) scram/hdlc inv N/N N/N Battery...............OK
Kp) clocking ST ST DTE Intf..............V.35/V.35

Kp) clocking ST ST DTE Intf..............V.35/V.35

Kp) clocking ST ST DTE Intf..............V.35/V.35
Gp) LOS lead NONE NONE Data bus..............A

Gp) LOS lead NONE NONE Data bus..............A

Ep) enable loop YES YES Tp) test and monitor BEC

Ep) enable loop YES YES Tp) test and monitor BEC
Np) near loopback OFF OFF Pp) monitor leads and status

Np) near loopback OFF OFF Pp) monitor leads and status

Np) near loopback OFF OFF Pp) monitor leads and status
Fp) far loopback ON OFF A) Alarm Enable......YES

Fp) far loopback ON OFF A) Alarm Enable......YES

[1,2] DIU 2130 >

Advertising