HEIDENHAIN TNC 640 (34059x-05) ISO programming - Manual (Page 674)

Index
674
TNC 640 | User's ManualDIN/ISO Programming | 1/2015
Plan view................................. 554
PLC and NC synchronization.... 322
Pocket table............................. 181
Polar coordinates........................ 96
Fundamentals........................... 96
Programming.......................... 232
Positioning................................ 542
With Manual Data Input......... 542
With tilted working plane.... 356,
443
Preset table...................... 500, 516
Transferring test results.......... 516
Principal axes....................... 95, 95
Probing a plane........................ 525
Processing DXF data
Basic settings......................... 258
Filter for hole positions........... 271
Selecting a contour................ 263
Selecting hole positions
Single selection................ 268
Selecting machining positions 267
Setting layers......................... 260
Setting the datum.................. 261
Program...................................... 99
Editing.................................... 106
Opening a new program........ 103
Organization............................. 99
Structuring.............................. 143
Program call
Any desired program as
subprogram............................ 279
Program defaults...................... 375
Program Management:See File
Management............................ 111
Programming graphics............. 241
Programming tool movements. 104
Program run............................. 562
Execute.................................. 563
Interrupt................................. 564
Mid-program startup.............. 569
Optional block skip................. 573
Overview................................ 562
Resuming after interruption.... 565
Retraction............................... 567
Program-section repeat............ 277
Projection in three planes......... 554
Protection zone........................ 581
Q
Q parameter
Export..................................... 323
Transfer values to the
PLC................................ 322, 323
Q parameter programming.... 292,
328
Additional functions................ 304
Angle functions...................... 299
Calculation of circles.............. 300
If-then decisions..................... 301
Mathematical functions.......... 297
Programming notes....
294, 329, 330, 331, 333, 335
Q parameters................... 292, 328
Checking................................ 302
Local parameters QL.............. 292
Nonvolatile parameters QR.... 292
Preassigned............................ 339
R
Radius compensation............... 199
Entering.................................. 200
Outside corners, inside
corners................................... 201
Rapid traverse.......................... 168
Reading out machine parameters....
336
Recessing and undercutting..... 469
Reference system................ 95, 95
Replacing texts......................... 110
Retraction................................. 567
After a power interruption...... 567
Retraction from the contour..... 366
Returning to the contour.......... 571
Rotary axis............................... 436
Reduce display M94............... 438
Shortest-path traverse: M126. 437
Rounding corners M197........... 371
S
Screen layout............................. 71
Search function........................ 109
Selecting a contour from DXF.. 263
Selecting positions from DXF... 267
Selecting the datum................... 98
Selecting the unit of measure.. 103
Select kinematics..................... 583
Setting the BAUD RATE....
588, 589, 589, 589, 589,
590, 590, 590, 590, 591
Software number..................... 587
SPEC FCT................................ 374
Special functions...................... 374
Spindle load monitoring............ 395
Status display............................. 76
Additional................................. 77
General..................................... 76
Straight line...................... 221, 233
String parameters.................... 328
Structuring programs................ 143
Subprogram.............................. 275
Superimposing handwheel
positioning M118...................... 364
Surface normal vector.............. 422
Switch-off................................. 482
Switch-on................................. 480
T
Teach In............................ 105, 221
Teach-in cut.............................. 388
Test Run................................... 559
Test run
Execute.................................. 561
Test Run
Overview................................ 559
test run
Setting speed......................... 549
Text File.................................... 399
Text file
Delete functions..................... 400
Finding text sections.............. 402
Opening and exiting............... 399
Text variables........................... 328
Tilted axes................................ 439
Tilting the Working Plane....
413, 414, 535
Tilting the working plane
Manual................................... 535
Tilting without rotary axes........ 434
TNCguide................................. 159
TNCremo.................................. 592
TNCremoNT............................. 592
Tool breakage monitoring......... 394
Tool change.............................. 186
Tool compensation................... 198
Length.................................... 198
Tool Compensation
Radius.................................... 199
Tool data................................... 170
Call......................................... 184
Delta values........................... 171
Entering into the program...... 171
Enter into the table................ 172
Tool data
Initiating................................. 178
Tool length............................... 170
Tool management.................... 190
Tool measurement................... 175
Tool name................................ 170
Tool number............................. 170
Tool radius................................ 170
Tool table.................................. 172
Edit, exit................................. 176
Editing functions..... 178, 193, 194
Input options.......................... 172
Tool usage file.................. 188, 582
Tool usage test......................... 188
Touch probe cycles................... 509
Manual Operation mode........ 509
See Touch Probe Cycles User’s
Manual
Touch probe monitoring............ 368
Traverse limits.......................... 581
Traversing reference marks...... 480
Trigonometry............................ 299