Yaskawa V7N Drive with DeviceNet - Manual (Page 26)

26
The Drive control circuits use various parameters to select functions and characteristics of the Drive.
Changing of parameter settings must be done in the Program mode, or by use of the Function
LEDs, if available (see TM.V7N.01, Section 4).
Drive Parameters
PARA-
ADDR
CLASS 100
NAME DATA
SETTING RANGE SETTING FACTORY
METER INST. 01 (AND UNITS) INCREMENT SETTING
0 0: n001 can be read and set;
n002 - n179 read only
1 1: n001 - n039 can be read and set
2 2: n001 - n079 can be read and set
3 3: n001 - n119 can be read and set
n001 101h 01h Parameter Selection / 4 4: n001 - n179 can be read and set
Initialization 5 5: n001 - n179 can be read and set 1 1
RUN command accepted during Program mode
6 6: Clear Fault History Only
7 7: Not Used
8 8: 2-wire Initialization (Japan Spec.)
9 9: 3-wire Initialization (Japan Spec.)
10 10:2 wire initialization (USA Spec)
11 11:3 wire initialization (USA Spec.)
n002 102h 02h Control Method Selection
0 0: V/f Control
1 0
1 1: Open Loop Vector
0 0: Digital Operator
n003 103h 03h Operation Method Selection
1 1: Terminal
1 3
2 2: Not Used
3 3: DeviceNet
0 0: Digital Operator Pot
1 1: Frequency Reference 1 (n024)
2 2: Not Used
3 3: Not Used
n004 104h 04h Reference Selection 4 4: Not Used
5 5: Not Used 1 9
6 6: Not Used
7 7: Multi-Function Analog Input (0 to 10V) (CN2)
8 8: Multi-Function Analog Input (4 to 20 mA) (CN2)
9 9: DeviceNet
n005 105h 05h Stop Method
0 0: Ramp to stop
1 0
1 1: Coast to stop
n006 106h 06h Reverse Prohibit
0 0: Reverse Run enabled
1 0
1 1: Reverse Run disabled
0 0: STOP key is effective regardless of
programming of n003
n007 107h 07h STOP Key Function
1 1: STOP key is effective only when sequence
1 0
command (per n003) is from Digital Operator
0 0: Frequency Reference from digital
n008 108h 08h Reference Selection -
operator pot 1 0
Digital Operator
1 1: Frequency Reference from n024
0 0: ENTER key must be pressed to write-in
n009 109h 09h Frequency Reference Setting new value
1 0
Method From Digital Operator 1 1: ENTER key does not have to be pressed
to write-in new value
Operation Selection 0 0: Disabled (operation continues)
n010 10Ah 0Ah When Digital Operator is 1 1: Enabled (motor coasts to a stop and fault 1 0
Disconnected is displayed)
n011 10Bh 0Bh Frequency - Max. - 50.0 to 400.0 0.1 (Hz) 60.0
n012 10Ch 0Ch Voltage - Max. -
0.1 to 255.0 (230V Drive)
0.1 (V)
230.0
0.2 to 510.0 (460V Drive) 460.0
n013 10Dh 0Dh
Frequency - Max. - 0.2 to 400.0
0.1 (Hz) 60.0
Voltage Point
n014 10Eh 0Eh Frequency - Midpoint - 0.1 to 399.9 0.1 (Hz) (Note 2)
n015 10Fh 0Fh Voltage - Midpoint
- 0.1 to 255.0 (230V Drive)
0.1 (V) (Note 2)
0.2 to 510.0 (460V Drive)
n016 110h 10h Frequency - Min. - 0.1 to 10.0 0.1 (Hz) (Note 2)
n017 111h 11h Voltage - Min.
- 0.1 to 50.0 (230V Drive)
0.1 (V) (Note 2)
0.2 to 100.0 (460V Drive)
Section 9
Drive Parameter Listing
(n001-n017)
IG.V7N.qxd:IG.V7N.qxd 6/5/07 3:22 AM Page 26