Yaskawa V7N Drive with DeviceNet - Manual (Page 27)

27
PARA- ADDR CLASS 100 NAME DATA SETTING RANGE SETTING FACTORY
METER INST. 01 (AND UNITS) INCREMENT SETTING
n018 112h 12h
Accel/Decel Time 0 0: 0.1
1 (sec) 0
Setting Unit 1 1: 0.01
n019 113h 13h Acceleration Time 1 (Note 4) 0.00 to 600.0
0.01 (sec)
n020 114h 14h Deceleration Time 1 (Note 4) - or
or
n021 115h 15h Acceleration Time 2 (Note 4) 0.0 to 6000
0.1 (sec)
10.0
n022 116h 16h Deceleration Time 2 (Note 4) (Dependent on n018 setting)
0 0: No S-curve
n023 117h 17h S-curve Selection
1 1: 0.2 second
1 0
2 2: 0.5 second
3 3: 1.0 second
n024 118h 18h Freq. Reference 1 (Note 4) 6.00
n025 119h 19h Freq. Reference 2 (Note 4) 0.00
n026 11Ah 1Ah Freq. Reference 3 (Note 4) 0.01 (Hz) 0.00
n027 11Bh 1Bh Freq. Reference 4 (Note 4)
- 0.00 to 400.00
(< 100 Hz) 0.00
n028 11Ch 1Ch Freq. Reference 5 (Note 4) or 0.00
n029 11Dh 1Dh Freq. Reference 6 (Note 4) 0.1 (Hz) 0.00
n030 11Eh 1Eh Freq. Reference 7 (Note 4) (>= 100 Hz) 0.00
n031 11Fh 1Fh Freq. Reference 8 (Note 4) 0.00
n032 120h 20h Jog Freq. Reference (Note 4) 6.00
n033 121h 21h
Frequency Reference Upper
- 0. to 110 1(%) 100
Limit
n034 122h 22h
Frequency Reference Lower
- 0. to 110 1(%) 0
Limit
0: 0.01 Hz (less than 100 Hz) / 0.1 Hz
Digital Operator 1: 0.1%
n035 123h 23h
Display Mode 2 - 39: rpm
1 0
40 - 3999: custom
0.1 to 49.5 Amps
n036 124h 24h Motor Rated Current -
(Up to 150% of Drive rated current)
0.1 (A) (Note 1)
0 0: Short term rating
n037 125h 25h
Electronic Thermal Overload
1 1: Standard rating 1 0
Protection (for OL1 fault)
2 2: Disabled
n038 126h 26h
Electronic Thermal Overload
- 1 to 60 1 (min) 8
Protection Time Constant
0 0: Operates only when Drive is running
n039 127h 27h
Cooling Fan Operation (continues operation for 1 minute after
1 0
Selection Drive is stopped)
1 1: Operates with power applied to Drive
n040 128h 28h Motor Rotation
0 0: Rotate C.C.W.
1 0
1 1: Rotate C.W. (or opposite direction)
n041 129h 29h
Acceleration Time 3
0.00 to 600.00
0.01 (sec)
(Note 4)
n042 12Ah 2Ah
Deceleration Time 3
or
or
(Note 4) -
n043 12Bh 2Bh
Acceleration Time 4
0.0 to 6000.0
0.1 (sec)
10.0
(Note 4)
n044 12Ch 2Ch
Deceleration Time 4
(Dependent on n018 setting)
(Note 4)
0 0: Fwd / Rev command (3 wire control)
n050 132h 32h Multi-function Input [can only be set in n052]
1
Selection 1 (Terminal S1) 1 1: Forward run (2 wire control) 1
(1)
2 2: Reverse run (2 wire control)
3 3: External Fault (N.O.)
n051 133h 33h
Multi-function Input
4 4: External Fault (N.C.) 2
Selection 2 (Terminal S2)
5 5: Fault Reset
1
(2)
6 6: Multi-step speed ref. cmd. A
n052 134h 34h
Multi-function Input
7 7: Multi-step speed ref. cmd. B 1
3
Selection 3 (Terminal S3)
8 8: Multi-step speed ref. cmd. C (0)
Drive Parameters - Continued
Section 9
Drive Parameter Listing
(n018-n052)
IG.V7N.qxd:IG.V7N.qxd 6/5/07 3:22 AM Page 27