Drive parameters - continued – Yaskawa V7N Drive with DeviceNet User Manual
Page 30
30
PARA- ADDR CLASS 100
NAME
DATA
SETTING RANGE
SETTING
FACTORY
METER
INST. 01
(AND UNITS)
INCREMENT SETTING
0
0:
Detection Disabled
1
1:
Detect only at set frequency;
operation continues
2
2:
Detect only at set frequency;
n096 160h
60h
Overtorque Detection (OL3)
coast to stop
1
0
3
3:
Detect during all frequency conditions;
operation continues
4
4:
Detect during all frequency conditions;
coast to stop
Overtorque Detection
n097 161h
61h
Selection (OL3)
0
0:
Detected by output torque
1
0
(Note 5)
1
1:
Detected by output current
n098 162h
62h
Overtorque Detection
Level (OL3)
-
30 to 200
1 (%)
160
n099 163h
63h
Overtorque Detection
Delay Time (OL3)
-
0.1 to 10.0
0.1 (sec)
0.1
n100 164h
64h
Up/Down Hold
0
0:
Disabled
Memory
1
1:
Enabled
1
0
n101 165h
65h
Speed Search
Deceleration Time
-
0.0 to 10.0
0.1 (sec)
2
n102 166h
66h
Speed Search Operation
-
Level
0 to 200%
1 (%)
150
n103 167h
67h
Torque Compensation Gain
-
0.0 to 2.5
0.1
1.0
(Note 4)
n104 168h
68h
Torque Compensation
-
Time Constant
0.0 to 25.5
0.1 (sec)
(Note 2)
n105 169h
69h
Torque Compensation
-
0.1 (W) or
Iron Loss
0.0 to 6550
1 (W)
(Note 1)
n106 16Ah
6Ah
Motor Rated Slip (Note 4)
-
0.0 to 20.0
0.1 (Hz)
(Note 1)
n107 16Bh
6Bh
Motor Line-to-line
-
0.001 (ohm)
Resistance
0.000 to 65.50
(Note 1)
n108 16Ch
6Ch
Motor Leakage
-
0.01 (mH)
Inductance (Note 1)
0.00 to 655.0
or 0.1 (mH)
(Note 1)
n109 16Dh
6Dh
Torque Compensation
-
1 (%)
Limit (Note 1)
0 to 250
150
n110 16Eh
6Eh
Motor No-load Current
-
0 to 99
1 (%)
(Note 1)
n111 16Fh
6Fh
Slip Compensation Gain (Note 4)
-
0.0 to 2.5
0.1
(Note 2)
n112 170h
70h
Slip Compensation Primary
-
0.0 to 25.5
0.1 (sec)
(Note 2)
Delay Time
n113 171h
71h
Slip Compensation Selection
0
0:
Disabled
1
0
During Regeneration (Note 1)
1
1:
Enabled
0
0:
Disabled
n115 173h
73h
Stall Prevention Above Base
(level is based on setting of n094)
Speed During Run
1
1:
Enabled
1
0
(level at Fmax is n094 x 0.4)
0
0:
Follows acc/dec #1 (n019, n020)
or acc/dec #2 (n021, n022)
n116 174h
74h
Stall Prevention During Run,
Note: Multi-Function input selectable
1
0
Accel/Decel Time Select
1
1:
Follows acc/dec #2 (n021, n022)
always
0
0:
Undertorque detection disabled
1
1:
Detected during constant speed running.
Operation continues after detection
Undertorque Detection
2
2:
Detected during constant speed running.
n117 175h
75h
Select (UL3)
Operation stops during detection
1
0
3
3:
Detected during all frequency conditions.
Operation continues
4
4:
Detected during all frequency conditions.
coast to stop
0 to 200%
n118 176h
76h
Undertorque Detection
-
Inverter rated current = 100%; if n097 = 0
1(%)
10
Level (detection by torque);
motor rated torque
becomes 100%
n119 177h
77h
Undertorque Detection
-
0.1 (sec)
Time
0.1 to 10.0
0.1
n120 178h
78h
Frequency Reference 9 (Note 4)
n121 179h
79h
Frequency Reference 10 (Note 4)
0.01 (Hz)
n122 17Ah
7Ah
Frequency Reference 11 (Note 4)
(< 100 Hz)
n123 17Bh
7Bh
Frequency Reference 12 (Note 4)
-
0.00 to 400.00
or
0.00
n124 17Ch
7Ch
Frequency Reference 13 (Note 4)
0.1 (Hz)
n125 17Dh
7Dh
Frequency Reference 14 (Note 4)
(>= 100 Hz)
n126 17Eh
7Eh
Frequency Reference 15 (Note 4)
n127 17Fh
7Fh
Frequency Reference 16 (Note 4)
Drive Parameters - Continued
Section 9
Drive Parameter Listing
(n096-n127)
IG.V7N.qxd:IG.V7N.qxd 6/5/07 3:22 AM Page 30