Yaskawa V7N Drive with DeviceNet - Manual (Page 29)

29
PARA- ADDR CLASS 100 NAME DATA SETTING RANGE SETTING FACTORY
METER INST. 01 (AND UNITS) INCREMENT SETTING
Analog Frequency Reference
n070 146h 46h Filter Time Constant - 0.00 to 2.00 0.01 s 0.10
(CN2, Voltage Ref Input)
n071 147h 47h
Analog Frequency Reference
- -255 to 255 1% 100
Gain (CN2, Current Ref Input)
n072 148h 48h
Analog Frequency Reference
- -100 to 100 1% 0
Bias (CN2, Current Ref Input)
Analog Frequency Reference
n073 149h 49h Filter Time Constant - 0.00 to 2.00 0.01 s 0.10
(CN2, Current Ref Input)
0 0: Multi-Function analog input disabled
1 1: Aux. Frequency reference
n077 14Dh 4Dh Multi-Function Analog 2 2: Frequency gain 1 0
Input CN2 Selection
3 3: Frequency bias
4 4: Voltage bias
n078 14Eh 4Eh
Multi-Function Analog Input 0 0: 0 - 10V
1 0
Signal Selection 1 1: 4 - 20 mA
n079 14Fh 4Fh Multi-Function Digital Input 0 0: Scans twice with 8 msec scan rate 1 0
Scan Rate Selection 1 1: Scans twice with 2 msec scan rate
n080 150h 50h Carrier Frequency -
1 to 4 (x 2.5 kHz)
1 3
7 to 9 (synchronous)
0 0: Not Provided
1 1: Continuous operation after power
n081 151h 51h
Momentary Power Loss recovery within 2 sec.
1 0
Ride-through Method 2 2: Continuous operation after power
recovery within control logic time
(no fault output)
n082 152h 52h
Number of auto restarts
- 0 to 10 1 0
attempts
n083 153h 53h Prohibit Frequency 1 - 0.00 to 400.0
0.01 (Hz)
0.00
or 0.1 (Hz)
n084 154h 54h Prohibit Frequency 2 - 0.00 to 400.0
0.01 (Hz)
0.00
or 0.1 (Hz)
n085 155h 55h Prohibit Frequency 3 - 0.00 to 400.0
0.01 (Hz)
0.00
or 0.1 (Hz)
n086 156h 56h Prohibit Frequency Deadband - 0.00 to 25.50 0.01 (Hz) 0.00
n087 157h 57h
Elapsed Time Function 0 0: Time elapses when power is On
0
Selection (5) 1 1: Time elapses when Drive is running
n088 158h 58h
Elapsed Operation Time
- 0 to 9999 hours 0
(Initial Value) (5)
n089 159h 59h DC Injection Current - 0 to 100 1 (%) 50
n090 15Ah 5Ah DC Injection Time at stop - 0.0 to 25.5 0.1 (sec) 0.0
n091 15Bh 5Bh DC Injection Time at start - 0.0 to 25.5 0.1 (sec) 0.0
n092 15Ch 5Ch
Stall Prevention During 0 0: Enabled
1 0
Deceleration 1 1: Disabled
n093 15Dh 5Dh
Stall Prevention During
- 30 to 200 1 (%) 170
Acceleration
n094 15Eh 5Eh
Stall Prevention Level During
- 30 to 200 1 (%) 160
Running
n095 15Fh 5Fh Frequency Detection Level - 0.00 to 400.0 0.01 (Hz) 0.00
or 0.1 (Hz)
Drive Parameters - Continued
Section 9
Drive Parameter Listing
(n070-n095)
IG.V7N.qxd:IG.V7N.qxd 6/5/07 3:22 AM Page 29