ProSoft Technology MVI69-HART - Manual (Page 167)

MVI69-HART ♦ CompactLogix Platform Index
HART Multi-drop Master Communication Module User Manual
ProSoft Technology, Inc. Page 167 of 169
March 29, 2012
Index
[
[HART PORT x COMMANDS] • 33
[HART PORT x] • 30
[MODULE] • 29
A
Adding the Module to an Existing CompactLogix
Project • 53
Adding the Module to an Existing MicroLogix Project •
53, 57
Analyzing Data for Port 1 • 74
Application Port Connection • 158
Auto-Poll Code • 32
Auto-Poll Data (HARTAutoPoll) • 52
Auto-Poll DB Address • 32
Auto-Poll Disabled Mode • 100
Auto-Poll Modes • 95
Auto-Poll Swap Float • 32
Auto-Polling • 98
B
Backplane Data Transfer • 86
Backplane Object (HARTBackplane) • 51
Battery Life Advisory • 3
Block 9902
Command Control • 37, 92
Block 9903
Command Disable Control Block • 37, 92
Block 9950
Read Command Error List • 93
Block 9998
Warm Boot • 94
Block 9999
Cold Boot • 94
Block Transfer Size • 29
Burst Mode • 97
Byte Count • 40
C
Channel Status Object (HARTCHStat) • 50
Clearing a Fault Condition • 62
COMMAND 00 - Read Unique Identifier • 115
COMMAND 01 - Read Primary Variable • 116
COMMAND 02 - Read Current And Percent Of Range
• 117
COMMAND 03 - Read Dynamic Variables • 118
COMMAND 06 - Write Polling Address • 119
COMMAND 108 - Write Burst Mode Command
Number • 155
COMMAND 109 - Burst Mode Control • 156
COMMAND 110 - Read All Dynamic Variables • 157
COMMAND 12 - Read Message • 120
COMMAND 13 - Read Tag, Descriptor and Date • 121
COMMAND 14 - Read PV Sensor Info • 122
COMMAND 15 - Read Output Information • 123
COMMAND 16 - Read Final Assembly Number • 124
COMMAND 17 - Write Message • 125
COMMAND 18 - Write Tag, Descriptor and Date • 126
COMMAND 19 - Write Final Assembly Number • 127
COMMAND 33 - Read Transmitter Variables • 128
COMMAND 34 - Write Damping Value • 129
COMMAND 35 - Write Range Values • 130
COMMAND 36 - Set Upper Range Value • 131
COMMAND 37 - Set Lower Range Value • 132
COMMAND 38 - Reset Configuration Changed Flag •
133
COMMAND 39 - EEPROM Control • 134
COMMAND 40 - Enter Exit Fixed Current Mode • 135
COMMAND 41 - Perform Transmitter Self Test • 136
COMMAND 42 - Perform Master Reset • 137
COMMAND 43 - Set PV Zero • 138
COMMAND 44 - Write PV Units • 139
COMMAND 45 - Trim DAC Zero • 140
COMMAND 46 - Trim DAC Gain • 141
COMMAND 47 - Write Transfer Function • 142
COMMAND 48 - Read Additional Transmitter Status •
143
COMMAND 49 - Write PV Sensor Serial Number • 144
COMMAND 50 - Read Dynamic Variable Assignments
• 145
COMMAND 51 - Write Dynamic Variable Assignments
• 146
COMMAND 52 - Set Transmitter Variable Zero • 147
COMMAND 53 - Write Transmitter Variable Units • 148
COMMAND 54 - Read Transmitter Variable
Information • 149
COMMAND 55 - Write Transmitter Variable Damping
Value • 150
COMMAND 56 - Write Transmitter Variable Sensor
Serial Number • 151
COMMAND 57 - Read Unit Tag Descriptor Date • 152
COMMAND 58 - Write Unit Tag Descriptor Date • 153
COMMAND 59 - Write Number Of Response
Preambles • 154
Command Control Blocks • 91
Command Count • 31
Command List Overview • 33
Commands Supported by the Module • 34, 36
Configuration/Error Status Flags (Cfg_Err) • 50
Configuring Module Parameters • 28
Configuring the RSLinx Driver for the PC COM Port •
21
Connecting Your PC to the Module • 23
Connecting Your PC to the Processor • 19
Contacting Technical Support • 165
Controller Tags • 48
D
Data Analyzer • 70, 74
Data Analyzer Tips • 76