Guardian Technologies Ademco VISTA-40 - Manual (Page 50)

Р 50 Р
Dialer Options (continued)
* 4 3 Dial Tone
D e t e c t i o n Determines whether the control will wait for a true dial tone before dialing, or if it
will wait for a predetermined delay before dialing (delay is programmed in Dial
Tone Pause field *42). The latter may be necessary in high-noise environment
Telco networks where noise can be confused with dial tone, resulting in
premature dialing. Enter 1 for true dial tone wait. If no dial tone is detected, will dial
at end of pause programmed in field *42. Enter 0 to pause for seconds entered
in field *42, then dial.
* 4 4 Ring Detection
C o u n t
Only applicable if central station initiated downloading will be used. Enter 00 to
disable ring detection. Enter 01-14 for ring counts of 1-14. Enter 15 to select
answering machine mode that allows the system to receive calls even when a
telephone answering machines is connected to the same phone line. In the
answering machine mode, the download caller should let the phone ring once,
then hang up, then call again within 30 seconds. The system, upon hearing one
ring followed by nothing, will not answer that call, but will ready itself to pick up on
the first ring the next incoming call that is received within 30 seconds (the
downloader calling again). DO NOT USE Т00У if 4285 Phone module is being
used. DO NOT USE Т01У if the VIM module is being used.
* 4 5 Primary Format This field selects the reporting format for use on the primary telephone line. Enter
the appropriate number for the primary format as follows: 0=Low Speed;
1=Contact ID; 2=Ademco High Speed; 3=Ademco Express.
Note: Contact ID (1) is the only reporting format that will send a "listen-in to
follow" message when using a n AAV unit.
* 4 6 Low Speed
Format (Primary)
Enter the appropriate value: 0=Ademco Low Speed; 1=Sescoa/Radionics
* 4 7 Secondary Format This field selects the reporting format for the secondary telephone line. Enter the
appropriate number for the secondary format as follows: 0=Low Speed; 1=Contact
ID; 2=Ademco High Speed; 3=Ademco Express
* 4 8 Low Speed
Format (Sec.)
Enter the appropriate value: 0=Ademco Low Speed; 1=Sescoa/Radionics
* 4 9 Checksum
Verification
Enter 1 for either or both primary/secondary formats to send a verification digit to
validate the message at the receiver without having to send two message rounds.
Valid for 3+1, 4+2, and Ademco High Speed reports. Enter 0 if not desired.
* 5 0 Sescoa/Radionics
S e l e c t
Enter 0 if Radionics format is to be used with hexadecimal 0-9, B-F reporting.
Enter 1 if SESCOA format is to be used with only numeric reporting (0-9). This
selection applies to both primary and secondary phone numbers.
* 5 1 Dual Reporting This field allows all reports to be sent to both primary and secondary phone
numbers. Enter 1 if it is desired that all reports are sent to both primary and
secondary phone numbers. If dual reporting is desired and Ademco High Speed
format is to be used at all, it must be selected as both the primary and secondary
transmission formats. If used with Split Reporting option 1 (1*34), alarms go to
both primary & secondary numbers, while all other reports go to secondary only. If
used with Split Reporting option 2, open/close and test messages go to both
lines, while all other reports go to primary.
* 5 2 Standard/
Expanded Report,
Primary
Enter 0 for standard or 1 for expanded reporting for the primary phone line.
Note: Expanded overrides 4+2 format.
* 5 3 Standard/
Expanded Report,
Secondary
Enter 0 for standard or 1 for expanded reporting for the secondary phone line.
Note: Expanded overrides 4+2 format.
*54-*78 Report Codes
For Zones 1-64, 87-99
Enter the appropriate report codes for each zone used in the system.
* 7 9 Zone Type
Restores For
Zone Types 1-8
Enter 1 to enable restore reporting for individual zone types. Enter 0 if no
restore report is desired for a zone type.