Strahl D1600mkII - Manual (Page 151)

143
Inser
t FX (2in2out x 2) /
Master FX / Final FX
Inser
t FX (2in2out x 2) /
Final FX
Inser
t FX
(1in2out x 2)
Inser
t FX
(1in1out x 4)
Inser
t FX
(1in1out x 8)
Ef
fect Control
Ef
fect Parameter List
These algorithms can be selected for an insert effect if
“2in2out
x 2 ” is selected for “Select Eff Type”. They can also be
selected for a final effect.
Large size LS1 – LS7
Category: Large size effects
32: LS1: St.Graphic 7band EQ
(Stereo Graphic 7band EQ)
This is a stereo 7-band graphic equalizer. The bar graph of the
gain setting for each band gives you a clear, visual idea of fre-
quency responses. You can select a center frequency setting for
each band from twelve types, according to the sound.
: Type
This parameter selects a combination of center frequencies for each
band.
33: LS2: St.Multiband Limiter
(Stereo Multiband Limiter)
This is a stereo multiband limiter.
34: LS3: Vocoder
This effect applies the character of the right channel signal
(Modulator) to the left channel signal input (Carrier). A com-
mon use of this effect is to produce the sound of various instru-
ments by inputting a voice to the Modulator via a microphone.
A special effect is also achieved by using rhythm or effect
sounds. Strings or distortion guitar sounds with a lot of harmon-
ics are suitable as a Carrier.
: Formant Shift
By offsetting the Carrier filter, you can adjust the height of the fre-
quency range to which the vocoder effect is applied. The tonal qual-
ity will change significantly.
: Noise Level
This parameter enables you to mix white noise with the Carrier.
: Modulator High Mix
This parameter sets the high-range output level of the right channel
sound (Modulator). If the modulator is a human voice, it will make
the words more clear.
: Vocoder/Carrier, : Wet/Dry
The “Vocoder/Carrier” parameter sets the balance between the
vocoder sound and the left channel sound (Carrier). The “Wet/Dry”
parameter sets the balance between the effect and dry sound. If you
wish to change the intensity of the vocoder effect, select “Wet” for
“Wet/Dry”, and adjust the balance using the “Vocoder/Carrier”
parameter.
35: LS4: St.Pitch Shifter
(Stereo Pitch Shifter)
This is a stereo pitch shifter. The pitch shift amount for the left
and right channels can be reversed from each other.
: L/R Pitch
When you select “Up/Dwn” for this parameter, the pitch shift
amount for the right channel will be reversed. If the pitch shift
amount is positive, the pitch of the left channel is raised, and the
pitch of the right channel is lowered. If an expression pedal etc. is
used to control the pitch, the pitch of the left channel will be con-
trolled.
: Mode, Fine
If Cntrl is controlling Pitch and you change Mode or Fine, you must
once again use Cntrl to readjust the Max and Min parameters.
Type (Type)........ 1:Wide1, 2:Wide2, 3:Wide3,
4:HalfW1, 5:HalfW2, 6:HalfW3,
7:Low, 8:WideLo, 9:Mid,
10:WideM, 11:High, 12:WideHi
Selects a combination of center frequen-
cies for each band
Trim (Trim) ...........................................0...100 Sets the input level
B1 (Band1 [dB])...............................–18...+18 Sets the gain of Band 1
B2 (Band2 [dB])...............................–18...+18 Sets the gain of Band 2
B3 (Band3 [dB])...............................–18...+18 Sets the gain of Band 3
B4 (Band4 [dB])...............................–18...+18 Sets the gain of Band 4
B5 (Band5 [dB])...............................–18...+18 Sets the gain of Band 5
B6 (Band6 [dB])...............................–18...+18 Sets the gain of Band 6
B7 (Band7 [dB])...............................–18...+18 Sets the gain of Band 7
Mix (Wet/Dry) ................ Dry, 1:99...99:1, Wet Sets the balance between the effect and
dry sounds
Ratio (Ratio) .....................1.0:1...50.0:1, Inf:1 Sets the signal compression ratio
Thrshl (Threshold [dB])........................–40...0 Sets the level above which the compres-
sor is applied
Attack (Attack) .....................................1...100 Sets the attack time
Relse (Release)...................................1...100 Sets the release time
LoOfst (Low Offset [dB])......................–40...0 Sets the low range gain of trigger signal
MdOfst (Mid Offset [dB])......................–40...0 Sets the mid range gain of trigger signal
HiOfst (High Offset [dB])......................–40...0 Sets the high range gain of trigger signal
GLevel (Gain Adjust [dB])........–Inf, –38...+24 Sets the output gain
Mix (Wet/Dry) ................ Dry, 1:99...99:1, Wet Sets the balance between the effect and
dry sounds
Insert Effect (2in2outx2)/
Final Effect
Carri (L [Carrier] Trim) ......................... 0...100 Sets the input level of left channel (Car-
rier)
Modul (R [Modulator] Trim).................. 0...100 Sets the input level of right channel
(Modulator)
Formnt (Formant Shift)........................ –2...+2 Sets the height of the frequency for the
vocoder effect
Respo (Response) .............................. 0...100 Sets the speed of the response to the
modulator input
NLevel (Noise Level) ........................... 0...100 Sets the noise mix level to the Carrier
LoGain (Low Gain [dB])................... –12...+12 Sets the low-range output level of the
vocoder
HiGain (High Gain [dB]) .................. –12...+12 Sets the high-range output level of the
vocoder
HiMix (Modulator High Mix)................. 0...100 Sets the high-range output level of the
modulator
Bal (Vocoder/Carrier) ...... Carrier, 1:99...99:1,
Vocode
Sets the balance between the vocoder
output and the Carrier
Mix (Wet/Dry) .................Dry, 1:99...99:1, Wet Sets the balance between the effect and
dry sounds
Mode (Mode)...................Slow, Medium, Fast Switches Pitch Shifter mode
L/R (L/R Pitch)......................Normal, Up/Dwn Determines whether or not the L/R pitch
shift amount is inverted
*Pitch (Pitch Shift [1/2tone]).............. –24...+24 Sets the pitch shift amount in steps of a
semitone
Fine (Fine [cent]) ....................... –100...+100c Sets the pitch shift amount in steps of
one cent
LDly (Lch Delay [msec]) .................... 0...1000 Sets the delay time for the left channel
RDly (Rch Delay [msec])................... 0...1000 Sets the delay time for the right channel
FPoint (Feedback Position) ............. Pre, Post Switches the feedback connection
Fdback (Feedback) ..................... –100...+100 Sets the feedback amount
HiDamp (High Damp [%]).................... 0...100 Sets the damping amount in the high
range
Spread (Spread).......................... –100...+100 Sets the width of the stereo image of the
effect sound
Mix (Wet/Dry) .................Dry, 1:99...99:1, Wet Sets the balance between the effect and
dry sounds
Inser
t FX (2in2out x 2) /
Final FX