Strahl D1600mkII - Manual (Page 153)

145
Inser
t FX (2in2out x 2) /
Master FX / Final FX
Inser
t FX (2in2out x 2) /
Final FX
Inser
t FX
(1in2out x 2)
Inser
t FX
(1in1out x 4)
Inser
t FX
(1in1out x 8)
Ef
fect Control
Ef
fect Parameter List
PA1
Category: Pre-amp simulator
48: PA1: Pre Amp Simulator
[Drive, NR2, Tone, Cabinet]
EB1 – EB3
Category: Bass multi
49: EB1: Bass Multi1
[CompT, Exctr, P4EQ, Cho/Fl, S.DLY]
50: EB2: Bass Multi2
[Dist, NR, Filter, Delay]
51: EB3: Bass Multi3
[Comp, P4EQ, Gate]
MS1
Category: Mic multi
52: MS1: Mic Multi
[CabRes, MicSim, Comp]
VO1 – VO2
Category: Vocal multi
53: VO1: Vocal Multi1
[Comp, Exctr, Pitch, S.Dly]
54: VO2: Vocal Multi2
[NR, DeEss, P4EQ, Cho/Fl, S.Dly]
Effects within multi-effect programs
GT1–VO2, and their parameters
Here are explanations of the parameters of each effect in the
multi-effect chains listed above.
Dist (Distortion)
This effect distorts the input sound
Drive
This effect models a compact effect unit or amp head.
*1: TubeOD, Classic, FatDist,Metal, Seattle,BigFuzz,TopBst,US.HiG, B.Stack,Direct
: TubeType
This parameter lets you vary the way in which the sound is distorted
by vacuum tubes. It simulates the way that distortion is influenced
by the amplitude, number of vacuum tubes, and their age. As you
increase the value of this parameter, non-linear distortion will
increase, and the overtone structure will change. It is best to raise the
Drive value, and then adjust the Tube value.
: TubeBias
This parameter adjusts the bias point of the vacuum tubes that dis-
tort the sound. In conjunction with the Tube parameter, this will vary
the overtone structure. The Bias parameter will have a greater effect
when the Tube setting is high.
NR (Noise Reduction)
This effect suppresses noise.
NR2 (Noise Reduction2)
This effect reduces the noise.
It is optimized specifically for use in a pre-amp chain.
: Threshold
Threshold must be adjusted according to the input level.
Since the input level of a guitar will differ depending on
whether it has single-coil or humbucking pickups, adjust the
input trim to an appropriate level before you adjust Threshold.
For a single-coil guitar, leave the trim set to approximately -10 at
a point where the noise is not too loud, and then adjust Thresh-
old so that the sound is not cut off unnaturally.
Since NR2 is optimized specifically for pre-amp, it operates dif-
ferently than NR.
Comp (Compressor/Limiter)
CompT (Tube Compressor/Limiter)
This is a vacuum tube type compressor.
Type (DriveType) ....... Tube, Crunch, Scream,
HotBox, Higain, Valve,
Crush, Scoop, Fuzz
Selects the drive type
Drive (Drive) ........................................1...100 Sets the degree of distortion
Treble (Treble)............................–15.0...+15.0 Sets the high-frequency tone
Level (Level) ........................................0...100 Sets the output level
Type (DriveType) .........................................*1 Drive type
Drive (DriveGain) ............................... 1…100 Depth of distortion
Level (Level) ....................................... 0…100 Output level
Tube (TubeType).................... SS, 1-99, Burn! Vacuum tube characteristics
Bias (TubeBias) .....................................0-100 Vacuum tube bias level
Thrsh (Threshold)........................ –40.0...–1.0 Sets the level at which the effect begins
to apply
Thrshl (Threshold)....................... –40.0...–0.0 Level at which noise reduction begins to
apply
Decay (Decay)....................................... 0...20 Decay time
Ratio (Ratio) ..................... 1.0:1...50.0:1, Inf:1 Sets the signal compression ratio
Thrshl (Threshold [dB]) ....................... –40...0 Sets the level above which the compres-
sor is applied
Attck (Attack)....................................... 1...100 Sets the attack time
Relse (Release) .................................. 1...100 Sets the release time
GLevel (Gain Adjust [dB])........................ –Inf,
–38...+24
Sets the compressor output gain
Ratio (Ratio) ..................... 1.0:1...50.0:1, Inf:1 Sets the signal compression ratio
Thrsh (Threshold[dB]) ......................... –40...0 Sets the level above which the compres-
sor is applied
Attck (Attack)....................................... 1...100 Sets the attack time
Relse (Release) .................................. 1...100 Sets the release time
GLevel (Gain Adjust[dB])......... –Inf, –38...+24 Sets the compressor output gain
Tube (TubeType).................... SS, 1-99, Burn! Vacuum tube characteristics
Inser
t FX
(1in2out x 2)