Strahl D1600mkII - Manual (Page 99)

91
COUNTER
Reference
SYSTEM /
USB
RECORD
TRACK
SONG /
CD
STORE
MARK
SCENE
TEMPO / RHYTHM
IN / LOC1... END / LOC4
AUTO PUNCH
LOOP
UNDO
TRIGGER
SCRUB
ENTER
INPUT / TUNER
EQ / PHASE
INSER
T
FX
MASTER FX / AUX
SOLO / MONITOR
METER / Tr VIEW
Tr
ST
ATUS
PA
N
FADER
TRANSPORT
Reference
Counter: Counter display
The counter located in the upper right of each page shows the
current location of the recorder.
1. Select TimeDisp Type...................................................
This switches the counter display. When you press the
“
” button at the left of the counter, the “Select Time-
Disp Type” dialog box will appear.
Select the desired type of display, and press the “OK”
button.
___.__.___ (MBT) : The current location will be shown in
measures from the beginning of the song.
From the left, the numbers indicate the Measure, Beat,
and Tick (1/96 beat).
___:__.___ (MSM)
: The current location will be shown as
an absolute time from the beginning of the song.
From the left, the numbers are Minutes: Seconds. Milli-
seconds (1/1000 second).
__:__.__F (MSF)
: The current location will be displayed
as the absolute time and the number of frames from the
beginning of the song. You will normally select this dis-
play type if you are using MTC synchronization.
From the left, the numbers are Minutes: Seconds. Frames
(1/30 second).
___.__Free (Free Time)
: The remaining time available
for recording on the currently selected drive will be
shown.
From the left, the numbers are Minutes. Seconds.
To change the current time of the counter, move the
cursor to the counter value, and use the [VALUE]
dial to change the value.
If the counter display is set to “Free,” the times in the
STORE, MARK, SCENE, A.PUNCH, LOOP, and
SCRUB pages will be displayed as absolute time
(MSM).
P1 Control: Foot switch/control
change device (pedal/MIDI)
settings
1. Pol(FootSwPolarity) ............................................[–, +]
This sets the polarity of the foot switch.
Connect a foot switch (such as the separately sold PS-1
option) to the front panel [FOOT SW] jack, and set this
parameter so that the polarity indicator “
” is lit when
you press the foot switch.
2. Func(FootSwFunction) ..... [PunchI/O, Play/Stop, Mark]
Select the function that the foot switch will control.
PunchI/O
: The foot switch will start/stop manual punch
recording.
Use the [TRACK STATUS] keys to set the desired track
to REC, begin playback, and press the foot switch at the
location where you wish to begin recording. Press the
foot switch again to stop recording.
Play/Stop
: The foot switch will start/stop playback.
Press the foot switch to start playback, and press it again
to stop playback.
Mark
: The foot switch will register a mark.
When you press the foot switch, a mark will be regis-
tered at that time location.
While this page is displayed, the foot switch will be
used only to verify the polarity, and the specified
function will be disabled. Also during tap recording,
the function you select here will be ignored, and the
foot switch will automatically function as a tap
marker.
3. Device(CtrlChgDevice).............[Pedal, A.Touch, P.Bend,
Velocity, NoteNum, CC#000…119]
Select the external device that will control the internal
effects of the D1600mkII. The effect selected by “Asn”
can be controlled in real-time.
Pedal
: An expression pedal can be used to control the
effect. Connect an expression pedal (separately sold
option: XVP-10, EXP-2 etc.) to the [EXPRESSION
PEDAL] jack, and operate the pedal to control the effect.
A.Touch, P.Bend, Velocity, NoteNum
: MIDI aftertouch,
pitch bend, velocity, or note number data can be used to
control the effect.
Connect the MIDI OUT of your external MIDI device to
the [MIDI IN] connector on the D1600mkII, and transmit
the selected MIDI data from the external MIDI device to
control the effect.
1. COUNTER
1
MBT
MSF
MSM
FreeTime
2. SYSTEM/USB
3 1 2 4 5