Panasonic DVCPRO50 AJ-D960EG - Manual (Page 64)

Setup menus
64 (E)
USER menu
<OPERATION>
Item Setting
No.
Superimposed
No.
Superimposed Description
display display
100 SEARCH 0000 DIAL
ENA 0001 KEY
101 SHTL MAX 0000
Ч
8.4
0001
Ч
16
0002
Ч
32
102 FF. REW 0000
×
16
MAX 0001
Ч
32
0002
Ч
50
103 AUDIO 0000 OFF
MUTE 0001 ON
104 REF 0000 OFF
ALARM 0001 ON
105 AUTO EE 0000 S/F/R
SEL 0001 STOP
0002 BLACK
0003 BLACK1
0004 GRAY
0005 GRAY1
The underline on the setting item denotes the initial setting.
This selects the direct search dial operation.
0: For direct search dial operations.
1: Operation is not transferred to the search mode unless the
search button is pressed.
This sets the maximum speed for shuttle operations.
0: 8.4 (7.0)
× normal speed
1: 16 × normal speed
2: 32 × normal speed
<Note>
The value for the DV/DVCAM format is shown in parenthesis
( ).
This sets the maximum speed for FF and REW operations.
0: 16 (32)
× normal speed
1: 32 (60) × normal speed
2: 50 (100) × normal speed
<Notes>
• The speeds given in the parentheses apply in the DVCPRO
(25 Mbps) mode.
• With the DV/DVCAM format, the maximum speed is set to
32 × regardless of this item’s settings.
This sets the status until the audio signal is output when
operation switches from the stop or search modes to the play
mode.
0: The time until the audio is output is shortened.
1: The audio is output after the status stabilizes.
<Note>
When set to 0 (OFF), the sound in the initially output part is
incomplete. Therefore, this setting is not recommended for
broadcasts.
This selects whether to warn the operator when the
REF.VIDEO signal has not been connected.
0: Warning is not given.
1: Warning is given by the flashing STOP lamp.
This selects the VTR mode in which the EE status is
established when the TAPE/EE switch is set to EE.
0: EE status is established in the STOP, FF or REW mode.
However, EE status is always established in EJECT mode
regardless of the TAPE/EE switch setting.
1: EE status is established only in the STOP mode. However,
EE status is always established in EJECT mode regardless
of the TAPE/EE switch setting.
2: EE status is established only in the STOP mode. However,
EJECT is set as follows depending on the setting of the
TAPE/EE switch.
At the EE setting;
The EE status is established.
At the TAPE setting; The picture turns black. The sound is
muted.
3: EE status is established in the STOP, FF or REW mode.
However, EJECT is set as follows depending on the setting
of the TAPE/EE switch.
At the EE setting;
The EE status is established.
At the TAPE setting; The picture turns black. The sound is
muted.
4: EE status is established only in the STOP mode. However,
EJECT is set as follows depending on the setting of the
TAPE/EE switch.
At the EE setting;
The EE status is established.
At the TAPE setting; The picture turns gray. The sound is
muted.
5: EE status is established in the STOP, FF or REW mode.
However, EJECT is set as follows depending on the setting
of the TAPE/EE switch.
At the EE setting;
The EE status is established.
At the TAPE setting; The picture turns gray. The sound is
muted.