Panasonic DVCPRO50 AJ-D960EG - Manual (Page 81)

ENGLISH
81 (E)
Setup menus
USER menu <AUDIO> (continued)
Item Setting
No.
Superimposed
No.
Superimposed Description
display display
726 REC CUE 0000 CUE
0001 CH1
0002 CH2
0003 CH1+2
0004 CH3
0005 CH4
0006 CH3+4
0007 CH1–4
727 PB FADE 0000 AUTO
0001 CUT
0002 FADE
728 EMBEDDED 0000 OFF
AUD 0001 ON
729 MONITOR 0000 OFF
MIX L 0001 CH1+2
0002 CH3+4
0003 CH1+3
0004 CH2+4
730 MONITOR 0000 OFF
MIX R 0001 CH1+2
0002 CH3+4
0003 CH1+3
0004 CH2+4
731 CUE OUT 0000 OFF
SEL 0001 ON
732 CUE SLOW 0000 STEP
0001 LINEAR
The underline on the setting item denotes the initial setting.
This selects the input signal recorded in CUE.
0: CUE IN
1: Audio CH1 input
2: Audio CH2 input
3: Audio CH1 and CH2 MIX signal
4: Audio CH3 input
5: Audio CH4 input
6: Audio CH3 and CH4 MIX signal
7: Audio CH1, CH2, CH3 and CH4 mixed signals
<Note>
The input signal is fixed at cue at all times regardless of this
setup menu’s setting if “SDTI” has been selected by the
INPUT SELECT switch.
This selects the processing method for the audio edit points
(IN point, OUT point) during playback.
0: According to the status during recording.
1: Forced CUT
2: Forced FADE
This selects whether to superimpose the audio data onto the
serial output.
0: Data is not superimposed.
1: Data is superimposed.
This makes it possible to select mixed signals for the monitor
output.
0: No mixing.
1: CH1 and CH2 are mixed and output to the left channel.
2: CH3 and CH4 are mixed and output to the left channel.
3: The CH1 and CH3 signals are mixed and output to the left
channel.
4: The CH2 and CH4 signals are mixed and output to the left
channel.
This makes it possible to select mixed signals for the monitor
output.
0: No mixing.
1: CH1 and CH2 are mixed and output to the right channel.
2: CH3 and CH4 are mixed and output to the right channel.
3: The CH1 and CH3 signals are mixed and output to the right
channel.
4: The CH2 and CH4 signals are mixed and output to the right
channel.
This selects whether or not the cue signal is to be output to the
main line output in the search mode.
0: CUE is not output.
1: CUE is output.
(This applies only when setup menu No. 721 (MONI CH
SEL) is not set to “MANU”.)
<Notes>
1. This function works only when a setting other than MANU has
been selected by setup menu item No. 721 (MONI CH SEL).
2. The main signal system output channels used for the CUE
output differ depending on the setting selected by setup
menu item No. 735 (MON AUTO SEL).
When L/R is selected: CUE is output to CH1 to CH4.
When L is selected:
CUE is output to CH1 and CH3.
When R is selected: CUE is output to CH2 and CH4.
For selecting the tape travel status (cue track playback status)
during slow-motion playback.
0: The output picture takes precedence, and the tape travels
at the STEP speed.
1: The cue track playback takes precedence and the tape
travels at the linear playback speed.
<Notes>
When “1” (LINEAR) has been selected:
• Set the TC/CTL switch to the TC position because the CTL
counter may not function properly.
• The picture may not appear as clearly as in the STEP mode.