Panasonic DVCPRO50 AJ-D960EG - Manual (Page 82)

Setup menus
82 (E)
USER menu <AUDIO> (continued)
Item Setting
No.
Superimposed
No.
Superimposed Description
display display
733 CUE OUT 0000 NORMAL
0001 DIRECT
734 MONI SEL 0000 OFF
INH 0001 ON
0002 ON1
735 MON AUTO 0000 L/R
SEL 0001 L
0002 R
736 AUDIO PB 0000 DIS
VR 0001 ENA
737 JOG PROC 0000 OFF
0001 ON
750 DV PB ATT 0000 OFF
0001 ON
751 REC PT 0000 OFF
MUTE 0001 ON
The underline on the setting item denotes the initial setting.
For selecting the output from the CUE OUT connector.
0: The timing is aligned with the output picture.
1: Whatever has been recorded on the tape is output with no delay.
<Note>
When “1” (DIRECT) has been selected, the timing of the out-
put picture and that of the cue output are not aligned properly.
However, this setting is effective only during DVCPRO (25
Mbps) mode playback.
This selects whether the operation of the MONITOR SELECT
button on the front panel is to be enabled or disabled.
0: Operation is enabled.
1: Operation is disabled.
2: Operation is disabled in the FULL display mode and
enabled only in the FINE display mode.
Although CUE is automatically output to the monitor output in
accordance with the operation mode when a setting other
than MANU has been selected by setup menu item No. 721
(MONI CH SEL), the MON AUTO SEL setup menu item is
used to select the monitor channel which is to be auto-
matically switched to CUE.
0: CUE is output to both the left and right channels.
1: CUE is output to the left channel only.
2: CUE is output to the right channel only.
This selects whether the playback level controls are to func-
tion in the EE mode when INT SG has been selected as the
setup menu item No. 700 (INT SG) setting.
0: The INT SG output level is fixed at UNITY.
1: The INT SG output level can be varied using the playback
level controls.
Selects the digital audio output slow signal processing in the
JOG/VAR/SHTL mode.
0: The sound from the digital audio without the slow signal
processing is output even in the STILL mode.
1: The sound from the digital audio output after the slow
signal processing is output.
This selects the audio output level during DV playback.
0: The audio output level is not attenuated.
1: The audio output level is attenuated (reduced).
This selects whether to mute the sound where recordings are
joined during DV/DVCAM playback.
0: The sound is not muted.
1: The sound is muted.
<Concerning the CUE output in the search mode>
The table below shows how the CUE output to the monitor and main signal system outputs differs according to how the setup menu item
(No. 721, No. 731 and No. 735) settings are combined.
731 721 735 Monitor output Main signal system output
CUE OUT MONI CH MON AUTO
Lch Rch CH1 CH2 CH3 CH4 SEL SEL SEL
L/R
MANU L PCM PCM
R
OFF
AUTO1 L/R CUE CUE
PCM PCM PCM PCM
| L CUE PCM
AUTO21 R PCM CUE
L/R
MANU L PCM PCM PCM PCM PCM PCM
R
ON
AUTO1 L/R CUE CUE CUE CUE CUE CUE
| L CUE PCM CUE PCM CUE PCM
AUTO21 R PCM CUE PCM CUE PCM CUE
<Notes>
• PCM audio signal output is muted when the VTR is played outside the –1 to +2.0 normal speed.
• When either AUTO1 or AUTO11 is selected, the PCM audio signal is output within –1 to +2.0 normal speed even in the automatic CUE output
mode.