Agilent Technologies E4438C - Manual (Page 137)

Index
Index I-1
A
add/remove programs , 1-6
adding datapacks , 1-19
adjustments
ALC Calibration , 4-32
ALC Modulation Driver Bias Calibration , 4-35
AM Audio Path Offset Calibration , 4-26
AM Gain Calibration , 4-40
Analog Bus ADC Calibration , 4-8
Burst Modulator Calibration , 4-27
Bypass Gain Adjust Calibration , 4-31
DCFM Calibration , 4-24
Digital Gain Adjust Calibration , 4-30
External Input Peak Detector Calibration , 4-25
FM 1/2 Path Ratio Gain Calibration , 4-19
FM In-Band DAC Offset Calibration , 4-17
FM Inverting Amplifier Offset Calibration , 4-18
FM Out-of-Band Calibration (Not Used with Option
UNJ or Option 506) , 4-21
FM Path Offset Calibration , 4-16
FM Scale DAC Offset Calibration , 4-15
FM/PM Out-of-Band Calibration (Option UNJ or
Option 506 Only) , 4-22
FM/PM YO Frequency Compensation Calibration ,
4-23
I/Q Gain/Offset/Quadrature Calibration , 4-41
I/Q Impairment Calibration , 4-42
Internal Reference Oscillator Calibration , 4-7
Internal Source Calibration , 4-10
KV versus Frequency Calibration , 4-13
Lock Angle Potentiometer Calibration (Not Used
with Option UNJ or Option 506) , 4-12
Modulation Source Relative Gain Calibration , 4-20
Power Level Accuracy, High Power Calibration ,
4-34
Power Level Accuracy, Low Power Calibration , 4-36
Power Search Calibration , 4-39
Prelevel Calibration , 4-28
Pretune Calibration (Option UNJ or Option 506
Only) , 4-9
relationships between adjustments , 4-5
Timebase DAC Calibration , 4-14
VBLO Mixer Bias Calibration , 4-29
VCO Bias Potentiometer Calibration , 4-11
administration configuration , 1-8
administration of service software , 1-7
ALC Calibration , 4-32
ALC Modulation Driver Bias Calibration , 4-35
AM Audio Path Offset Calibration , 4-26
AM Frequency Response , 3-14
AM Gain Calibration , 4-40
Analog Bus ADC Calibration , 4-8
B
Burst Modulation On/Off Ratio , 3-32
Burst Modulator Calibration , 4-27
Bypass Gain Adjust Calibration , 4-31
C
calibration
due date , 1-11
recommended calibration cycle , 3-2
tracking number , 1-11
type , 1-11
CDMA Adjacent Channel Power (Not Used with
Option UNB or Option 506) , 3-33
choose destination location screen , 1-4
configuring the software , 1-7
Custom I/Q RF Modulation Quality (Option 402
Only) , 3-29
D
datapacks
adding , 1-19
removing , 1-21
DCFM Calibration , 4-24
DCFM Frequency Offset Relative to CW , 3-17
destination folder , 1-4
device drivers, adding , 1-14
device type , 1-9
Digital Gain Adjust Calibration , 4-30
Digital Modulation Level Accuracy , 3-27
drivers
device , 1-14
test
adding , 1-16
removing , 1-19
Dual Arbitrary Waveform Generator Check , 3-39
DUT (Device Under Test), identifying , 1-8 , 1-23
DUT selection window , 3-5
E
equipment serial number in software , 1-11
exiting service software , 1-29 , 3-8
External Input Peak Detector Calibration , 4-25
F
FM 1/2 Path Ratio Gain Calibration , 4-19
FM Frequency Response , 3-13
FM In-Band DAC Offset Calibration , 4-17
FM Inverting Amplifier Offset Calibration , 4-18