Metrohm 774 Oven Sample Processor - Manual (Page 167)

7 Index
774 Oven Sample Processor, Instructions for use 159
monitoring the interfaces...........32
MOVE.........................................76
MOVE command .......................76
MOVE function...........................30
move the lift................................30
N
needle adapter...........................11
new rack types.........................120
no error ......................................99
normal state ...............................43
number of samples....................68
O
object tree................................102
oblique view .................................3
oils..............................................40
on beaker error: .........................71
on HEATER timeout:..................71
on SCAN timeout:......................71
operate interfaces......................32
operate the interfaces................32
operation via RS232 interface .101
other gases................................72
outlet hollow needle...................11
outlet tube..................................14
output.........................................97
output lines ................................98
oven control ............ 31; 37; 51; 78
oven heating block ....................37
oven method..............................40
oven settings..............................24
oven temperature ................31; 37
overheating ................................64
overpressure..............................38
overview .......................................1
P
packaging ....................................8
parallel interface ........................21
parallel/serial converter..............20
Parameter menu ..................45; 68
parameter report..................85; 87
parameters.................................68
parity: .........................................66
PCL3 emulation .........................21
peripheral instruments...............97
personal computer ....................88
pin assignment ..................97; 135
piston .........................................96
plastic granulates ......................40
play ............................................96
plug cover ....................................4
port.............................................93
port assignment.........................84
position samples .......................30
position vial ................................50
positioning the lift.................50; 77
power consumption.................141
power supply ...............................8
POWER-UP method ..................36
predefined positions..................50
pre-dried sample vials ...............41
prep......................................79; 84
prepar ........................................94
preparation ..........................73; 94
prepare the tubing system ........31
printer emulations ......................21
printing reports ..........................85
process control..........................35
program .....................................63
program version ........................63
programmable HEATER com-
mand.....................................38
properties of the RS232 interface .
............................................131
protective cover ........................... 4
pulse ..........................................99
pump ...................................31; 78
pump delivery ..........................140
purge .........................................40
Q
quitting error message ..............58
R
RACK .........................................82
rack code.............................64; 90
rack definitions ..........................25
rack exchange ............................. 6
rack number ..................64; 70; 90
rack type ....................................90
raise the lift.................................50
ramps.........................................38
redefine instrument settings......53
Ready1.......................................99
rear panel..................................... 5
rear view....................................... 5
rec. interval ................................70
receive errors...........................104
receiving signals........................97
recording ...................................70
redefining instrument settings...83
reduction valve ..........................38
relative humidity.......................141
release .................................79; 95
Remote connections .................16
Remote control tree.................106
Remote interface .................32; 97
replacing fuse.............................. 9
report type .................................70
report: ........................................70
reserved positions .....................91
RESET........................................23
reset sample rack......................82
residual moisture .......................41
result report ...............................70
rinse ...........................................84
rinse position .......................65; 90
rinsing ........................................73
rinsing inlet.................................73
rinsing position ..........................40
Rmt CTL:....................................74
rod magnets ................................ 7
roll-up selection .........................59
rotary knob.................................39
rotate the rack............................30
RS control:.................................67
RS232 connection .........16; 18; 20
RS232 CTL: ...............................74
RS232 interface .....20; 27; 32; 135
RS232 socket ..........................136
S
safety considerations ................10
safety specification..................141
SAMPLE command ...................76
sample counter..........................43
sample determination................41
SAMPLE function.......................31
sample preparation ...................40
sample rack .....................6; 13; 89
sample sequence................ 33; 69
sample vials......................... 7; 158
sample weight ........................... 40
SAMPLE: ................................... 76
save method.............................. 75
SCAN command ....................... 52
SCAN function........................... 32
SCAN timeout:........................... 71
scanning input data .................. 20
scanning the remote interface .. 79
scanning the RS232 interface... 80
SCN:Rm .................................... 79
SCN:Rm command................... 79
SCN:RS ..................................... 80
SCN:RS command.................... 80
second parameter..................... 43
Seiko.......................................... 21
send errors .............................. 105
sensitive samples...................... 38
septum seals ............................... 7
sequences................................. 33
Serial connection....................... 20
serial interface ........................... 20
serial/parallel converter ............. 21
series of commands.................. 33
service ..................................... 141
servicing .................................. 141
servicing personnel ................. 143
set sample position ............. 31; 50
setting the remote lines............. 81
setting up..................................... 8
shift direction:............................ 70
shift position ........................ 65; 90
shift rate..................................... 70
shift sample rack ....................... 30
SHIFTRATE.......................... 55; 83
short result report ...................... 85
signal output.............................. 74
socket strip .............................. 3; 5
soft termination.......................... 35
software-handshake................ 131
solenoid valve...................... 31; 78
SOPs........................................ 152
special beaker ........................... 91
special beaker 1 ........................ 65
special cables ........................... 97
special position ......................... 91
spezial position.......................... 65
standard rack ............................ 89
standard substances .............. 152
START 737................................. 99
start a method ..................... 35; 57
START device1.................... 81; 99
START dos1 .............................. 99
start of the series....................... 33
start sequence..................... 33; 69
status ......................................... 43
status messages ..................... 103
stop bit:...................................... 66
STOP device1............................ 99
stop process ............................. 57
storage .................................... 141
stream of gas ............................ 38
stroke path................................. 63
stroke speed.............................. 70
surface moisture........................ 38
system drift ................................ 41
T
target temperature..................... 51
technical data.......................... 140