Banner EZ-SCREEN Low-Profile Safety Light Curtain Systems - Manual (Page 19)

P/N 13348
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Overview
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
EZ-SCREEN LP
Instruction Manual
17
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Components and Specifications
2.7 Specifications
2.7.1 General Specifications
Short Circuit Protection All inputs and outputs are protected from short circuits to +24V dc or dc common.
Electrical Safety Class
(IEC 61140: 1997)
III
Safety Rating Type 4 per IEC 61496-1, -2; Category 4 PL e per EN ISO13849-1, SIL3 per IEC 61508; SIL CL3 per
IEC 62061
Operating Range 0.1 m to 7 m (4" to 23')
Range decreases with use of mirrors and/or lens shields:
Lens shields – approximately 10% less range per shield.
Glass-surface mirrors – approximately 8% less range per mirror.
See the specific mirror data sheet or the Banner Safety Catalog for further information.
Resolution 14 mm or 25 mm, depending on model (Reduced Resolution OFF)
Effective Aperture Angle
(EAA) Meets Type 4 requirements per IEC 61496-2, Section 5.2.9
± 2.5° @ 3 m
Enclosure Size: See Figure 2-6
Materials: Extruded aluminum housing with yellow polyester powder finish standard (optional clear
anodized or static-dissipative nickel-plated finish) and well-sealed, rugged die-cast zinc
end caps, acrylic lens cover, copolyester access cover. Nickel-plated models also have
static-dissipative acrylic lens cover and nickel-plated end caps.
Rating: IEC IP65
Operating Conditions Temperature: 0° to +55° C (+32° to 131°F)
Max. Relative Humidity: 95% maximum relative humidity (non-condensing)
Shock and Vibration EZ-SCREEN LP components have passed vibration and shock tests according to IEC 61496-1. This
includes vibration (10 cycles) of 10-55 Hz at 0.35 mm (0.014") single amplitude (0.70 mm peak-to-
peak) and shock of 10 g for 16 milliseconds (6,000 cycles).
Mounting Hardware Emitter and receiver each are supplied with a pair of swivel end-mounting brackets and two swivel
side-mount brackets. Models longer than 690 mm also include additional side-mount bracket(s) for
center support. Mounting brackets are 14-gauge/1.9 mm cold-rolled steel, black zinc finish.
Cables and Connections See Section 2.3 for recommended cables. If other cables are used with the EZ-SCREEN LP, the user
must verify suitability of these cables for each application.
Certifications
Figure 2-4. Emitter or receiver product identification label
Label is located on back of housing, near cable end
www.bannerengineering.com M/N: SLPR14-270P8 S/N: H00584011401201012 SUPPLY: 24V dc +/- 15%, 0.150A dc max.
RANGE: 0.1 - 7 m TEMPERATURE RATING: 0 to 55 °C ENCLOSURE RATING: IP65 DEFINED AREA: 270mm
RESOLUTION (RED. RES. OFF/ON): 14mm / 34mm EFFECTIVE APERTURE ANGLE: ≤ 2.5° at 3m RESPONSE TIME: 10.5ms
SAFETY RATING: Type 4 per IEC 61496, EN ISO 13849-1 Cat. 4 PL e, SIL 3 per IEC 61508 OSSD RATING: Imax = 0.5A; Von > Vin - 1.5 Vdc
140120
1012H