Banner EZ-SCREEN Low-Profile Safety Light Curtain Systems - Manual (Page 41)

P/N
39
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Overview
P/N 140044 rev. E 39
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
EZ-SCREEN LP
Instruction Manual Installation and Alignment
Figure 3-23. Emitter; generic hookup
Figure 3-22. Parallel emitter/receiver hookup for easy sensor interchange (“swapability”)
+24V dc 0V dc
8-pin male
Euro-style
face view
Bn (Pin #1)
Gn/Ye (#7)
Bu (#6)
Bk (#5)
Wh (#4)
Vi (#8)
Or (#3)
Or/Bk (#2)
Close to reset
n.c.*
n.c.*
n.c.*
n.c.*
*NOTE: Pins 2, 3, 4 and 5 either are not connected, or are paralleled to same
color wire from the 8-pin receiver cable.
+24V dc 0V dc
8-pin male
Euro-style
face view
Bn (Pin #1)
Gn/Ye (#7)
Bu (#6)
Bk (#5)
Wh (#4)
Vi (#8)
Or (#3)
Or/Bk (#2)
Open to test
n.c.*
n.c.*
n.c.*
n.c.*
*NOTE: Pins 2, 3, 4 and 5 either are not connected, or are paralleled to same
color wire from the 8-pin receiver cable.
Wire Color
(Pin #)
Default OR Fault OSSD Follow
Wire
Function
DIP Switch Settings* Wire
Function
DIP Switch Settings* Wire
Function
DIP Switch Settings*
Receiver Emitter Receiver Emitter Receiver Emitter
Brown (#1) +24 dc 2-channel EDM
Aux. Out Fault OFF +24 dc 1-channel EDM
Fault Out Fault ON +24 dc 1-channel EDM
Aux. Out Fault OFF
Orange/Black (#2) EDM2 Fault Aux
Orange (#3) EDM1 EDM1 EDM1
White (#4) OSSD2 OSSD2 OSSD2
Black (#5) OSSD1 OSSD1 OSSD1
Blue (#6) 0V dc 0V dc 0V dc
Green/Yellow (#7) Ground Ground Ground
Violet (#8) Reset Reset Reset
*NOTES (for Parallel hookup):
- Reset will reset both emitter and receiver in all three options.
- OR Fault configuration will indicate if the emitter or the receiver has locked out, see Section 3.5.5.
- Emitter Test function is not available when the emitter is connected in parallel (swapable hookup) to the receiver.
Only pertinent DIP switch settings are specified.
Vi
Individual Cordsets
Bn
Or
Or/Bk
Wh
Bu
Bk
Gn/Ye
Emitter (Reset Hookup) Emitter (Test Hookup)
0V dc +24 dc
8-pin male
Euro-style
face view
Bn (#1)
Or (#3)
Wh (#4)
Gn/Ye (#7)
Bu (#6)
Vi (#8)
Bk (#5)
*NOTE: Pins 3, 4, and 5 either are not connected (n.c.), or are paralleled to same color wire from the 8-pin receiver cable (see Section 3.7 and Figure 3-22).
n.c.*
n.c.*
n.c.*
Or/Bk (#2)
0V dc +24 dc
8-pin male
Euro-style
face view
Bn (#1)
Or (#3)
Wh (#4)
Gn/Ye (#7)
Bu (#6)
Vi (#8)
Bk (#5)
n.c.*
n.c.*
n.c.*
n.c.*
Or/Bk (#2)
Close to reset
or n.c.*
Splitter Cordsets
Pigtail or
DELPE.. Cordset
CSB.. Splitter
Cordset
DEE2R..
Pigtail or
DELPE.. Cordset
Model CSB.. splitter cordsets and DEE2R..
double-ended cordsets allow easy
interconnection between an EZ-SCREEN LP
receiver and emitter, providing a single
“homerun” cordset (see Section 2.3 Cordsets).
See table below or
Section 2.3 for pinout
n.c.*
Open to test
RDLP-8..D Cordsets