Document Outline

• Hybrid Logic Overview
• Modulating Logic Overview
• Outdoor Reset Concept
• Control Layout
• Extension Layout
• Features
  • Make Sure You Have the Right Control
• Installation
  • Mounting the Enclosure
  • Install the Sensors
    • System Sensor Installation
    • Outdoor Sensor Installation
  • Wiring
    • Wiring the Power
    • Wiring the Sensors
    • Wiring the Shutdown, Tstat, or Setback
    • Wiring the Prove
    • Wiring the Indirect Domestic Hot Water (DHW) Call
    • Wiring the System Output
    • Wiring the Boilers
    • Wiring Boiler Activation or On/Off Staging Boilers
    • Wiring Multi-Stage Boilers
    • Wiring to Modulating Boilers
    • Wiring the 4-20mA Modulating Boilers
    • Wiring Voltage Modulating Boilers
    • Connecting to the Extensions and 4-20mA EMS Interface
    • Connecting to BACnet Interface Module
  • Activate the Battery
• HYBRID Startup Menu
• Modulating Startup Menu
• Startup Settings
  • Program Change Switch Setting
    • Startup Sequence
    • Boiler Type
    • Sensor Type
    • EMS Input Mode
    • EMS 4mA and 20mA Set Points
  • HYBRID Startup Settings
    • Switch Set Point
    • Switch Differential
    • Switch Delay
    • Heavy Load Sequence 2nd Group
    • Condensing and Non-Condensing Boiler Type
    • Condensing and Non-Condensing Boiler Number
  • HYBRID Modulating Boiler Settings
    • Modulating Output Type
    • Modulating Mode
  • HYBRID Staging Boiler Settings
    • Staging Output Type
    • Staging Mode
  • Modulating Boiler Settings
    • Boiler Number
    • Modulating Output Type
    • Modulating Mode
  • Startup Settings (Continued)
    • Prove/Indirect Domestic Hot Water (DHW) Priority
    • Indirect Domestic Hot Water Set Point
    • Shutdown/Tstat/Setback Mode
    • Boost Mode
    • Sensor Fault
  • Setting the Control to Factory Defaults
• BACnet MSTP Communication Menu
  • BACnet Mode
    • BACnet Baud Rate
    • MS/TP Address
    • BACnet ID
• Operating Settings
  • Program Change Switch Setting
    • Season
    • Set Point
    • Reset Ratio
    • Offset
    • Outdoor Cutoff Temperature
    • Minimum Water Temp
    • Maximum Water Temp
• HYBRID Operating Menu
• Modulating Operating Menu
  • System Settings
    • Setback
    • Purge Delay
    • System Run-On
    • Lead Boiler Rotation
    • Standby Time
    • Last Stage Hold
    • Lead Stages
  • Modulating Boiler Operating Settings
    • Gain
    • Lag Delay
    • Soft-Off Delay
  • Staging Boiler Operating Settings
    • Reaction Time
    • Minimum Runtime
  • Day - Night Schedule
    • Set Time
  • Maintenance
    • System & Outdoor Sensor Trim
    • Output Modulation Trim
    • Configuration
  • Display
  • Boiler Status
    • Display Modulating Boiler Status
  • Display Messages
• Boiler Stage Menu
  • Mode
    • Ignition %
    • Modulation Start %
    • Copy Settings - Boiler A Only
• Troubleshooting
• Specifications
• Hybrid - Outdoor Reset - BACnet Variable list
• Modulation - Outdoor Reset - BACnet Variable list
• Modulation - Set Point - BACnet Variable list
• BACnet PICS Statement
• Piping and Wiring Diagrams
  • Hybrid Piping Diagram
  • Hybrid Wiring Diagram
  • Modulating Piping Diagram
  • Modulating Wiring Diagram