Document Outline

• Title Page
• Preface
  • Audience
  • Conventions
    • Command conventions
    • GUI conventions
    • Symbols
    • Network topology icons
  • About the H3C SR8800 documentation set
  • Obtaining documentation
  • Technical support
  • Documentation feedback
• Contents
• Product overview
  • Chassis views
    • SR8802 chassis views
    • SR8805 chassis views
    • SR8808 chassis views
    • SR8812 chassis views
  • Power supply system
    • AC power modules
    • DC power modules
  • Cooling system
    • Fan trays
    • Airflow design for the SR8802 and SR8805 and SR8812
    • Airflow design for the SR8808
• Preparing for installation
  • Safety recommendations
    • General safety recommendations
    • Electricity safety
    • ESD prevention
    • Router moving
    • Laser safety
  • Examining the installation site
    • Weight support
    • Temperature
    • Humidity
    • Cleanness
    • EMI requirements
    • Grounding
    • Power supply
    • Space
  • Rack-mounting
  • Installation tools
    • Accessories supplied by the router
    • User-supplied tools and equipment
• Installing the router
  • Inspecting the router
  • Installing the router in a rack
    • Installation preparation
    • Installing slide rails and cage nuts to the rack
      • Installing slide rails
      • Installing cage nuts
    • Installing the cable management brackets
      • Installing the cable management brackets on the SR8808
      • Installing the cable management brackets on the SR8802/SR8805/SR8812
    • Installing the mounting brackets
    • Installing an impedance carrier (optional)
    • Installing the router to a rack
    • Verifying the installation
  • Grounding the router
  • Installing the power system
    • Installation preparation
    • Installing a DC power module
    • Installing an AC power module
      • Installing NEPS800-A and NEPS2000-A AC power modules
      • Installing an NEPS3500-A AC power frame
      • Installing an NEPS1800-A AC power module
  • Installing a card
    • Installation preparation
    • Installation procedure
  • Installing a subcard
    • Installation preparation
    • Installation procedure
  • Connecting power cords
    • Prerequisites
    • Connecting an AC power cord
      • Connecting an NEPS800-A or NEPS2000-A AC power cord
      • Connecting an NEPS3500-A AC power cord
    • Connecting a DC power cord
  • Verifying the installation
• Connecting the router to the network
  • Logging in to the router
    • Connecting the console cable
      • Introduction
      • Connection procedure
    • Setting up a configuration environment
  • Powering on the router
    • Verification before power-on
    • Powering on the router
    • Verification after power-on
  • Connecting the router to the network
    • Connecting the router to the network through an AUX cable
    • Connecting the router to the network through an Ethernet twisted pair cable
    • Connecting the router to the network through an optical fiber
      • Introduction to fiber connector
      • Precautions
      • Installing a transceiver module
      • Connection procedure
      • Installing fiber management tray (optional)
  • Cable routing recommendations
• Hardware management
  • Displaying the electrical label data for your router
  • Displaying the card information
  • Rebooting your router
  • Displaying the power supply system
  • Configuring temperature alarm thresholds for a card
    • Configuring temperature alarm thresholds for a card
    • Displaying the temperature information
  • Configuring in-service hardware failure diagnosis
  • Displaying the operating state of fans
  • Displaying the alarming information of a card
  • Verifying and diagnosing transceiver modules
    • Introduction to transceiver modules
    • Verifying transceiver modules
    • Diagnosing transceiver modules
• Troubleshooting
  • Configuration terminal problems
    • No terminal display
    • Garbled terminal display
  • Power supply system failure
  • Fan failure
  • MPU failure
  • LPU failure
  • Interface failure
  • Technical support
• Replacement procedures
  • Replacing a power supply system
    • Preparing for the replacement
    • Replacing a DC power module
    • Replacing an AC power module
      • Replacing an NEPS800-A or NEPS2000-A AC power module
      • Replacing an NEPS3500-A AC power frame and an NEPS1800-A power module
  • Cleaning the air filter of a power module
  • Replacing a card
    • Preparing for the replacement
    • Replacement procedure
  • Replacing a subcard
    • Replacement procedure
  • Replacing a fan tray
    • Replacing a fan tray for an SR8802/SR8805/SR8812
    • Replacing a fan tray for an SR8808
  • Replacing a chassis air filter
    • Replacing chassis air filters for an SR8808
    • Replacing the air filter for an SR8802/SR8805/SR8812
  • Replacing a CF card
  • Replacing a transceiver module
• Appendix A Technical specifications
  • Environment requirements
  • Chassis specifications
  • Card specifications
    • MPU specifications
    • SPC card specifications
    • SPE base card specifications
    • MPE base card specifications
    • Subcard specifications
      • PIC specifications
      • MIC subcard specifications
    • OAA module specifications
    • Transceiver module and cable specifications
      • SFP modules
      • SFP+ fiber modules and SFP+ cables
      • XFP fiber modules
  • Fan tray specifications
  • Power system specifications
• Appendix B LEDs
  • Power module LEDs
  • Fan LEDs
  • MPU LEDs
    • CF card status LED
    • Network management port LEDs
    • LPU status LEDs
    • MPU status LEDs
  • SPC card LEDs
    • LINK/ACT LED
    • Combo interface LED
    • LINK and ACT LEDs
  • SPE/MPE card LED
  • Subcard LEDs
• Appendix C Lightning protection
  • Connecting the AC power supply to a power strip with lightning protection
  • Installing a lightning protector for a network port
    • Required tools
    • Installation procedure
    • Installation precautions
• Appendix D Engineering labels
  • Labels for cables
    • Labels for signal cables
    • Labels for power cords
    • Generic labels
  • Labels for devices
  • Filling in labels
  • Affixing labels
    • Affixing a label to a signal cable
    • Affixing a label to a power cord
    • Affixing a generic label
    • Affixing a label to a device
  • Guidelines
  • Examples
    • Engineering labels for network cables
    • Engineering labels for optical fibers
    • Engineering labels for DC power cords
    • Engineering labels for AC power cords
    • Engineering labels for devices
• Appendix E Cable management
  • Cable management guidelines
  • Cable management examples
• Index