Toshiba Strata DK 16 User Manual
Page 77
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
2-53
PROGRAM 10-2
SYSTEM ASSIGNMENTS, PART 2 OF 3
H
Z
Z
1
P
S
H
S
0
SELECT = 2
Button/LEDs
2
Light LEDs as defined by the table below.
ALL LEDs with an "X" should be lit when you finish
20
19
10
18
17
16
15
6
14
13
12
11
10
4, 11
09
4
08
Button/LED
X
LED On
LED Off
–
Station External Amp Conference
Two CO Line Conference
“TRNS” Immediate (Soft Key)
Executive Override Warning Tone/ON
External Page included with All Call Page
Privacy Override Warning Tone/ON
Send Auto Callback Camp-on Tone
3
CO Line 3 min Beep Tone
No DTMF Tone Return
7
BGM connected to QSTU (DK8), PORT 19;
BGM connected to PEKU, Circuit 3
9,10
Display Dialed Number/1min.
–
No External Amplifier Connected
No Two CO Line Conference
“TRNS” Normal (Soft Key)
Executive Override Warning Tone/OFF
Not Included
Privacy Override Warning Tone/OFF
No Callback Tone
No Beep Tone
DTMF Tone Return
Telephone connected to CKT
Telephone connected to CKT
Display Dialed Number/15 sec.
2
2
2
Standard Tel., CO Ring
per Prog. 10-1, LED 06
VM ID Code DTMF Signal Time 80 ms
DISA Busy Tone, 0.5 second cadence
8
MW cancel from VM; dial
6 4
& Station No.
Ringing Modes/3
Hunt/C.F. override from DSS console's phone
Tone First (from DSS Console)
2
Standard Tel. CO Ring Distinctive
160 ms
DISA Busy Tone, 0.25 second cadence
MW cancel from VM: Automatic
Ringing Modes/2
Hunt/C.F. override from DSS console
Voice First (from DSS Console)
NOTE: Shaded areas apply to DK16 only
PESU (DK16), Circuit 8
9,10
07
5
06
05
04
03
02
01
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data lights LEDs 02, 14, 15 and 16.
3. Called party receives notification tone when calling party activates Automatic Callback.
4. BGM connected to QSTU/PSTU/PEKU/PESU/KSTU, will be sent to electronic and digital telephone speakers and external page
(optional). Important: Power must be turned off and on for BGM assignments to be effective.
5. Ring pattern for standard telephones: distinctive ring on incoming CO calls, is: 0.2 sec. on, 0.4 sec. off, 0.2 sec. on, 3.4 sec. off; intercom
ring is always 1 sec. on, 3 sec. off. This doesn't apply to voice mail ports (Program 31, LED 17 on) which are always standard ring.
6. External speakers and designated digital and electronic telephones are paged by dialing
Intercom 3 9
. The
All Call Page
button is
used only to page designated digital and electronic telephones.
7. Deletes DTMF tones returned to digital and electronic telephones when dialing from dialpad or speed dialing; also deletes auto dial digits
sent to callers that are call forwarded to voice mail. This does not affect the actual DTMF tones sent out to the CO or voice mail.
8. 0.5 second cadence, Bell Standard Busy Tone, should be enabled so outside callers are not confused by STRATA 0.25 second busy
tone when calling busy number on DISA line calls.
9. If BGM source is assigned to KSTU or PSTU slot in Program 19, system automatically assigns KSTU or PSTU CKT 4 as a BGM source.
10. Important: LED 19 should be OFF unless external amplifiers are used for two CO line/station conference (see Program 10-3). If LED 19
is ON, the station may be unbalanced and receive HUM if external amplifier with Auto-Gain-Control is not connected.
11. BGM connected to QSTU, circuit 2, (DK8) Port 19 may require an isolation transformer per Section 100-816-207