Gilderfluke&Co 16 Bit CD-Quality Digital Audio Systems - Manual (Page 54)

¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒoÓ Reload Defaults:
This command is used to reload the default conditions for the variables set on the Trigger Menu of
the AB/DR-3000. The default condition for this screen enables only the Start Track command on the front
panel pushbutton input. All the defaults for all the menus can be loaded from the front panel by de-
pressing both the up and down keys simultaneously as power is first applied to the AB/DR-3000.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒxÓ eXit Setup Mode:
This command is used to exit the setup mode. If you hit this command in error, hitting an <ESC>ape
key will get you back to the menu.
For compatibility with other products that might be on the same RS-422 serial network, this com-
mand asks you to enter a ÔYÕ or ÔNÕ. This lets them know that the setup mode has been exited on this
card. If you hit this command by mistake, then you can hit the <ESC>ape key to get back to where you
were before.
All other AB/DR-3000 and Brick Brains in the same serial network have their serial ports disabled while
any card in the system is in setup mode. This is the only command to which they will respond. After the
initial 'X', all the other cards wait for a 'Y' or 'N' before they will start accepting other serial commands
again. If you find that you are having trouble communicating with any of the cards in the system, try en-
tering an ÔXNÕ to trick it into thinking you have exited the configuration mode.
G ILDERFLUKE & C O . ¥ 205 S OUTH F LOWER S T . ¥ B URBANK , C ALIF . 91502-2102 ¥ 818/840-9484 ¥ FAX 818/840-9485
46 of 92