Gilderfluke&Co 16 Bit CD-Quality Digital Audio Systems - Manual (Page 60)

Ôh) hours for tolling- 00:00-02:00 / 08:00 to 23:59Õ
This is the setting you use if you want to let your neighbors sleep. Assuming the previous
day has also been set in the same way, it will carry the tolling up through 23:59 before this
dayÕs schedule takes over. If the next dayÕs schedule is also set in the same way then it will pick
up at midnight of the next morning. In this way the hours for tolling will roll over from day to
day without a break.
c) If any other identical times are entered, then Ô24 hour operationÕ is selected and displayed.
d) If 00:00 to 00:00 are entered as the start and end times, then no hours of operation are se-
lected for that dayÕs schedule and ÔnoneÕ is displayed. Unless:
1) If there are hours of operation selected on the all-week schedule, and this is a weekday
(Monday through Friday) or the ÔAll-WeekÕ selection is set for ÔSunday through SaturdayÕ,
then these hours will be displayed and used.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒjÓ Next Schedule:
This simply displays the next of the eight schedules. It saves you having to go into the Ômore....Õ com-
mand to select another schedule.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒmÓ More.....:
This command allows you to select from the other menus:
1) Main Menu. This brings you back to the main menu.
2) Triggers. If mono ROMs are installed, it will ask if you want to setup the Left or Right Triggers.
3) SMPTE Setup. This is where you enter the SMPTE triggers for starting spiels. This menu is available
only if you have selected the SMPTE IN mode for the repeater.
4) This selects this menu.
5) Volume. This is where you set up the Digital Audio Bus and volumes.
6) Status Outputs. This is where you setup what the two status outputs do.
7) Diagnostics. This displays the status of the mutes zones, switch, analog, and DMX inputs.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒoÓ Reload Defaults:
This command is used to reload the default conditions for the variables set on the Real Time Clock
Menu of the AB/DR-3000. All of the defaults for all of the menus can be loaded from the front panel by
depressing both the up and down keys simultaneously as power is first applied to the AB/DR-3000.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒxÓ eXit Setup Mode:
This command is used to exit the setup mode. If you hit this command in error, hitting an <ESC>ape
key will get you back to the menu.
For compatibility with other products that might be on the same RS-422 serial network, this com-
mand asks you to enter a ÔYÕ or ÔNÕ. This lets them know that the setup mode has been exited on this
card. If you hit this command by mistake, then you can hit the <ESC>ape key to get back to where you
were before.
All other AB/DR-3000 and Brick Brains in the same serial network have their serial ports disabled while
any card in the system is in setup mode. This is the only command to which they will respond. After the
initial 'X', all the other cards wait for a 'Y' or 'N' before they will start accepting other serial commands
again. If you find that you are having trouble communicating with any of the cards in the system, try en-
tering an ÔXNÕ to trick it into thinking you have exited the configuration mode.
G ILDERFLUKE & C O . ¥ 205 S OUTH F LOWER S T . ¥ B URBANK , C ALIF . 91502-2102 ¥ 818/840-9484 ¥ FAX 818/840-9485
52 of 92