Gilderfluke&Co 16 Bit CD-Quality Digital Audio Systems - Manual (Page 65)

- S TATUS O UTPUTS M ENU -
The AB/DR-3000 has two optically isolated status outputs. This menu is used to control how they are
used. They can be set to operate when the left or right repeaters are playing, at specific periods (if the
Real Time Clock Option has been installed), or at specific points during a spiel being played out of the
left side of the repeater (or a stereo spiel). The last option is only available if the SMPTE Output has been
enabled. If it has not, then the area where the table is shown will be blanked.
-Sixteen Bit Digital Audio System rev 1.19 copyright 1996 Gilderfluke & Co. DCM-
- card __0 Status Output Menu -
a) modify table | c) Status #1- Left running | e) Pulse #1 output
b) Pulse length- 9.9 sec. | d) Status #2- Right running | f) Pulse #2 output
01) 1 on 01:23 __5 02) 1 pul 01:02 all 03) 2 pul 51:25 all 04) 2 on 02:02 __2
05) 1 off 01:24 __5 06) 2 off 03:03 __2 07) _______________ 08) _______________
09) _______________ 10) _______________ 11) _______________ 12) _______________
13) _______________ 14) _______________ 15) _______________ 16) _______________
17) _______________ 18) _______________ 19) _______________ 20) _______________
21) _______________ 22) _______________ 23) _______________ 24) _______________
25) _______________ 26) _______________ 27) _______________ 28) _______________
29) _______________ 30) _______________ 31) _______________ 32) _______________
33) _______________ 34) _______________ 35) _______________ 36) _______________
37) _______________ 38) _______________ 39) _______________ 40) _______________
41) _______________ 42) _______________ 43) _______________ 44) _______________
45) _______________ 46) _______________ 47) _______________ 48) _______________
49) _______________ 50) _______________ 51) _______________ 52) _______________
m) more.... o) reload defaults X) eXit
please enter command-
All the activities of the two status outputs is also shown on the two decimal points of the seven seg-
ment displays on the front of the AB/DR-3000.
¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥¥
ÒaÓ Modify Table:
This command is used to alter the fifty-two entries in the pulse table. It is unavailable if the SMPTE
Output has been disabled on this repeater. This command asks:
1) Whether you want this entry to act on the #1 or #2 Status Output. You can enter a zero if you
want to clear an existing entry.
2) You can set the output to:
a) Turn on. The output will stay on until turned off or pulsed by one of the other commands.
b) Turn off. The output will stay off until turned on or pulsed by one of the other commands.
c) Pulse for the period set by the Pulse Length.
3) Minutes and seconds into a spiel when you want this to happen.
4) The specific spiel you want this to happen during, or a zero if you want this to happen during
all spiels (shown by ÔallÕ in place of the specific spiel number on the menu entry).
Entries to this table must be made consecutively. Any empty entry will be interpreted as
the last entry in the table, even if more entries can be found further on. The values of each of
the entries can be in any order.
G ILDERFLUKE & C O . ¥ 205 S OUTH F LOWER S T . ¥ B URBANK , C ALIF . 91502-2102 ¥ 818/840-9484 ¥ FAX 818/840-9485
57 of 92