Yokogawa In-Situ Gas Analyzer TDLS200 - Manual (Page 18)

Standard Accessories
Calibration Cell: - Used for off-line calibrations and
validations
- Stainless steel 316 with free standing
frame
- Connects Launch and Detect with
72.6cm (28.6") OPL
Flow Cells: - Used for extracted sample streams at any
location
- 316SS low volume fixed alignment; 50ºC,
5.5 bar (80psig) max
- Enhanced for 200ºC, 20 Bar (290psig),
Sapphire window, Kalrez o-rings and can
be constructed from 316SS, Monel A400,
Hastelloy C-276, Carpenter 20 and other
materials on request to suit the process
Isolation Flanges: - Used for additional protection for in-situ
or by-pass installations
- 2” or 3” 150# or 300# ANSI RF, 4”150#,
DN80 PN16 welded 5/8” or M16” bolt
studs included sapphire 20 Bar (290 psig)
or BK-7 5.5bar (80 psig) isolation window
- Kalrez window seal o-ring rated max
200ºC
- 316SS, Monel A400, Hastelloy C-276,
Carpenter 20, other on request
Note: Must use in conjunction with alignment flanges
Utility Panel: - Used for convenient field installation of
utilities, configurations for
- Single, dual or four analyzers
- Manual or automatic on-line validation
(controlled by analyzer)
- Safe area (GP), Div 2 purged or non-
purged, ATEX CAT 2G components
- Purge flowmeters with integral needle
valve, glass tube variable area
- Swagelok double ferrule stainless steel tube
fittings and tubing standard
- Panel mounted or fiberglass (NEMA 4X/
IP65), with viewing window
- 5A 24VDC power supply, output to
analyzer – requires VAC input power
Note: Custom configuration available to suit customer requirements
Integration:
- Used for convenient analyzer & extractive
system/flow cell integration
- Free standing frame, galvanized steel with
304SS roof
- Fiberglass enclosure with powder coated
steel frame
- Heat tracing and insulation for flow cells
and sample handling
- 316SS and/or Monel A400 wetted parts –
other on request
- Sample handling and conditioning
systems to suit applications
- Stream switching manual or automatic
(controlled by analyzer)
Note: Custom configuration available to suit customer requirements
Display and Software functions
TruePeak Software has multiple levels, the default (or start page) is
the Main Menu:
Main Menu Displays: - Concentration & Units (% or ppm)
- Transmission %
- Status (warm-up, OK, Warning, Fault,
etc.)
- Temperature (Fixed, Active Ambient or
Active)
- Pressure (Fixed or Active)
Main Menu:
Basic Menu
- Configure, 3 functions
- View Spectra, 2 functions
- Data, 3 sub-menus
- Trends
Advanced Menu - Configure, 9 sub-menus
(User Password) - Calibrate & Validate, 3 sub-menus
- Data, 4 sub-menus
- Trends,
Active Alarms - List of active alarms
Shut Down Analyzer - Instructions to close TruePeak local or
VAC
Calibration Functions:
Off-line Calibrations:
- Zero calibration
- Zero off-set
- Span calibration
- Transmission
- Dark current
- peak search
Off-line Validations: - Check gas #1
- Check gas #2
- Check gas #3
On-Line Validations: - Manual
- Automatic
Setup Functions:
Configuration:
- Process Path Length
- Pressure
- Temperature
- Units
- System I/O
- System
- Valve Control
- Laser Spectra & Control
Diagnostics:
Warnings include:
- Detector signal low
- Transmission low
- Spectrum noise high
- Process pressure out of range
- Process temperature out of range
- Concentration out of range
- Board temperature out of range
- Validation failure
Faults include: - Laser temperature out of range
- Detector signal high
- Detector signal lost
- Peak center out of range
Output Settings:
Analog Output:
- Channel 1
- Channel 2
- Channel 3
- Warning Mode
- Fault Mode
- Field Loop Check
- AO CH calibration
3-3
IM 11Y01B01-01E-A 6th Edition :Feb 13, 2013-00
<3. GENERAL SPECIFICATIONS>