4-3. transducer block parameters, 4-3-1. transducer block parameters ph202, 4-3. transducer block parameters -9 – Yokogawa DO202 2-Wire Dissolved Oxygen Analyzer User Manual
Page 67: 4-3-1. transducer block parameters ph202 -9
Profibus 4-9
4-4-3. Transducer block parameters
4-4-3-1. Transducer block parameters PH202
Parameter
default
Alternatives
Unit r/W Slot, Index data Type
(byte,bit) (bytes)
Primary value Type
111(pH)
R
4, 27
unsigned16 (2)
Measured Value
pH
R
4, 28
DS-33 (5)
Status
R
4, 28
DS-33 (5)
Sensor type pH
pH/ORP sensor(160)
pH/ORP sensor(160)
R
4, 30
unsigned16 (2)
Sensor mV
mV
R
4, 31
float (4)
Secondary value Parameters
Value
ºC
R
4, 42
DS-33 (5)
Status
R
4, 42
DS-33 (5)
Secondary value unit
˚C
˚F
R/W 4, 43
unsigned16 (2)
Sensor temp comp
Automatic(2)
Off(0), Manual(1)
R/W 4, 44
unsigned8 (1)
Sensor temp man value
ºC
R/W 4, 45
float (4)
Temperature sensor
Pt1000(148)
Pt100(128), 5k1(150), 3kBalco(145),
R/W 4, 46
unsigned16 (2)
8k55(151), 350(153), PTC10k(158),
6k8(157)
Temp. connection type
1
R
4, 47
unsigned8 (1)
Process compensation
Disabled(0)
Enabled(1)
R/W 4, 167(1.0) unsigned32 (4)
Temperature Coefficient
mV/
10ºC R/W 4, 159
float (4)
Tertiary value Parameters
Tertiary value type
None(1)
ORP(2), rH(3)
R
4, 48
unsigned16 (2)
Value
mV
R
4, 49
DS-33 (5)
Status
R
4, 49
DS-33 (5)
Calibration Parameters
Calibration High
pH
R/W 4, 32
float (4)
Calibration Low
pH
R/W 4, 33
float (4)
Cal min span
pH
R
4, 34
float (4)
Slope check
Enabled(1)
Disabled(0)
R/W 4, 167(1.1) unsigned32 (4)
Slope
%
R/W 4, 35
float (4)
Slope unit
%(1342)
%(1342)
R
4, 36
unsigned16 (2)
Zero check
Enabled(1)
Disabled(0)
R/W 4, 167(1.0) unsigned32 (4)
Zero
mV
R/W 4, 37
float (4)
Zero unit
mV(1243)
pH(1422)
R/W 4, 38
unsigned16 (2)
Isopotential pH
pH
R/W 4, 39
float (4)
Tertiary zero
mV
R/W 4, 51
float (4)
Calibration method
not calibrated(0)
one point(107), two point(108), other(255)
R/W 4, 40
unsigned8 (1)
Date of Calibration
R
4, 41
DS-21
Stable Time
5.0 sec
S
R/W 4, 97
float (4)
Stable Value
0.02pH
pH
R/W 4, 98
float(4)
diagnostic Settings
Glass impedance
ohm R
4, 52
float (4)
Glass impedance Lo Lim
ohm R/W 4, 101
float (4)
Glass impedance Hi Lim
ohm R/W 4, 102
float (4)
Glass impedance check Enabled(1)
Disabled(0)
R/W 4, 167(2.2) unsigned32 (4)
Glass impedance circuit High(1)
Low(0)
R/W 4, 167(2.0) unsigned32 (4)
Glass impedance comp. Enabled(1)
Disabled(0)
R/W 4, 167(2.1) unsigned32 (4)
Glass impedance exceeds
low limit (E4.1)
Hard fail(1)
Soft fail(0)
R/W 4, 166(2.2) unsigned32 (4)
Glass impedance exceeds
high limit (E5.1)
Hard fail(1)
Soft fail(0)
R/W 4, 166(2.3) unsigned32 (4)
Reference impedance
ohm R
4, 53
float (4)
Reference impedance
low limit
ohm R/W 4, 103
float (4)
Reference impedance
high limit
ohm R/W 4, 104
float (4)
Reference impedance check
Enabled(1)
Disabled(0)
R/W 4, 167(2.5) unsigned32 (4)
IM 12A00A01-61E