Yokogawa Button Operated MV2000 - Manual (Page 111)

4-38 M-4662
To set a command for writing measurement
channels
Syntax YM p1,p2,p3,p4,p5,p6,p7<terminator>
p1 Registration number (1 to 16)
p2 Command type (W)
p3 First channel number (measurement
channel number)
p4 Last channel number (measurement
channel number)
p5 Slave device address (1 to 247)
p6 First register number (40001 to 49999,
400001 to 465535)
p7 Type of data assigned to the register (INT16,
FLOAT_B, FLOAT_L)
Query YM[ p1]?
Example Register the following command in command
registration number 3: Write the measured data
of channels 003 to 006 to registers 40003 to
40006 on the slave device at address 7.
YM3,W,003,006,7,40003,INT16
To set a command for writing computation
channels
Syntax YM p1,p2,p3,p4,p5,p6,p7<terminator>
p1 Registration number (1 to 16)
p2 Command type (W-M)
p3 First channel number (computation channel
number)
p4 Last channel number (computation channel
number)
p5 Slave device address (1 to 247)
p6 First register number (40001 to 49999,
400001 to 465535)
p7 Type of data assigned to the register (INT16,
UINT16, INT32_B, INT32_L, FLOAT_B,
FLOAT_L)
Query YM[ p1]?
Example Register the following command in command
registration number 2: Write the 16-bit signed
integer computed data of channels 101 to 105
to the first register 40003 on the slave device at
address 5.
YM2,W-M,101,105,5,40003,INT16
Description • You can execute this command on models
with the /C2 or /C3 serial interface option.
• You can use this command when the serial
interface protocol is set to Master. For serial
interface settings, see section 2.3.
• The settings specified with this command take
effect when you save the settings with the XE
command and power-cycle the MV.
To set a command for writing floating type data
into Modbus registers
Syntax YM p1,p2,p3,p4,p5,p6,p7<terminator>
p1 Command number (1 to 16)
p2 Command type
W Write data from measurement
channels
W-M Write data from computation
channels
p3 First channel number
Measurement channel number (1 to 48) if
p2 is set to W
Computation channel number (101 to 124) if
p2 is set to W-M
p4 Last channel number (1 to 48)
Measurement channel number (1 to 48) if
p2 is set to W
Computation channel number (101 to 124) if
p2 is set to W-M
p5 Server number (1 to 16)
p6 First register number (40001 to 499991,
400001 to 465536)
p7 Register data type
INT16 16-bit signed integer
UNIT16 16-bit unsigned integer
INT32_B 32-bit signed integer (Big
Endian)
INT32_L 32-bit signed integer (Little
Endian)
FLOAT_B 32-bit floating point (Big
Endian)
FLOAT_L 32-bit floating point (Little
Endian)
Example Using command number 1, write the data from
measurement channels 1 to 16 to the registers
at server number 3 starting from register number
40001 in 32-bit floating point format (Big Endian).
YM1,W,1,16,3,40001,FLOAT_B
Query YM?
Description The selectable range of the first channel number
(p3) and last channel number (p4) varies
depending on the model.
WR Sets the instrument information
output
Syntax WR p1,p2,p3,p4<terminator>
p1
Memory/Media state ON/OFF
p2 Self diagnosis ON/OFF
p3 Communication error ON/OFF
p4 Memory stop ON/OFF
Query WR?
Example Output various information.
WRON,ON,ON,ON
XE Activates Basic Setting Mode
Syntax XE p1<terminator>
p1
Store or discard the settings (STORE,
ABORT)
Example Save the setup data of the basic setting
commands.
XESTORE
Description To activate the settings that are changed with
the basic setting commands, you must save the
settings with the XE command. Make sure to
save the settings with the XE command before
changing from Basic Setting Mode to Operation
Mode. Otherwise, new settings will not take
effect.
4.6 Basic Setting Commands