EVCO EVF328J9 - Manual (Page 17)

EVCO S.p.A. EVF 300 series | Installer manual ver. 1.1 | Code 144F300E114
Page 17 of 62
6 USER INTERFACE
6.1 Device switch-on/off in manual
mode
Operate as follows to switch the device on/off in manual
mode:
1. Make sure no procedures are in progress.
2. Hold the“SWITCH-ON/OFF” key down for 1 s.
When the power is switched back on, the device displays the
status that it was in at the time it was cut-off.
It is also possible to switch the device off through the multi-
function input. If the device has been switched off through the
activation of the multi-function input, it cannot be switched on
in manual mode (until the input has been deactivated).
6.2 Starting the cooking cycle
Operate as follows to start the cooking cycle:
1. Ensure that the cooking timer is set and that no
other procedure is in progress.
2. Press and release the "START/STOP" key: the
“TIMER” LED will switch on and the bottom part of
the “UPPER” display will show the residual count if
the cooking timer.
6.3 Stopping the cooking cycle
Operate as follows to stop the cooking cycle:
1. Make sure no procedures are in progress.
2. Hold the “START/STOP” key down for 1 s: the
buzzer will be activated for 3 s, the “TIMER” LED
will switch off and the bottom part of the “UPPER”
display will show “End” flashing for 3 s.
6.4 The displays
6.4.1 The top part of the "UPPER" display
If the device is on, the top part of the “UPPER” display will
show the following information:
- if the CFG parameter is set at 0, the chamber
temperature
- if the CFG parameter is set at 1, the top
temperature
Also see paragraph P5.
If a cooking cycle is in progress, the top part of the “UPPER”
display will show the following information:
- if the CFG parameter is set at 0, the chamber
temperature
- if the CFG parameter is set at 1, the top
temperature
Also see paragraph P5.
If the "weekly programmed switch-on" has been activated, the
top part of the "UPPER" display will be off.
If the device is off, the top part of the "UPPER" display will be
off.
6.4.2 The bottom part of the "UPPER" display
If the device is on, the bottom part of the "UPPER" display will
show the value of the cooking timer.
If a cooking cycle is in progress, the bottom part of the
"UPPER" display will show the residual count of the cooking
timer.
If the "weekly programmed switch-on" function has been
activated, the bottom part of the "UPPER" display will show the
switch-on time of the next weekly programmed switch-on.
If the device is off, the bottom part of the “UPPER” display will
show the following information:
- if the c8 parameter set at 0, will be off
- if the c8 parameter set at 1, the time
6.4.3 The top part of the "LOWER" display
If the device is on, the top part of the “LOWER” display will
show the following information:
- if the CFG parameter is set at 0, the power
distributed at the top alternately to the power
distributed at the floor for 10 s
- if the CFG parameter is set at 1, the floor
temperature
Also see paragraph P6.
If a cooking cycle is in progress, the top part of the “LOWER”
display will show the following information:
- if the CFG parameter is set at 0, the power
distributed at the top alternately to the power
distributed at the floor for 10 s
- if the CFG parameter is set at 1, the floor
temperature
Also see paragraph P6.
If the "weekly programmed switch-on" has been activated, the
top part of the "LOWER" display will be off.
If the device is off, the top part of the "LOWER" display will be
off.
6.4.4 The bottom part of the "LOWER" display
If the device is on, the bottom part of the "LOWER" display will
show the value of the cooking timer.
If a cooking cycle is in progress, the bottom part of the
“LOWER” display will show the following information:
- if parameter t0 is set at 0, the minimum duration
of steam injector switch-on
- if the parameter t0 is set at 1, the number of
steam injections in cyclic mode.